Best Dynabolts for bike?

[Badfish]

Hello, The names Ryan.
Due to losing 3 bikes over the past year and a half we have come to realise we cannot be to secure.
My question is, What is the dynabolt that is widely used and thought highly of amongst the fellow NZ Bikers? what has worked well against thiefs and what hasn't?

I will read the bike security threads when i have time, I did a quick search but nothing specifically dynabolt oirintated.

Thanks,
Ryan

[jellywrestler]

theifs

Thiefs; i before e except after c......
what's failed with your last dyna bolts that wont this time????
a grinder will get through if needed maybe it's time to up the sophistication of both your dictionary and your security and look at other methods too

[bogan]

Well, if you throw it hard enough and hit em fair in the noggin, any old dynabolt should do the trick!

Think its more of a complete setup though, hope you get it sussed and don't lose any more.

[St_Gabriel]

Thiefs; i before e except after c......
what's failed with your last dyna bolts that wont this time????
a grinder will get through if needed maybe it's time to up the sophistication of both your dictionary and your security and look at other methods too

Oh the irony

thieves not thiefs

[Drew]

Two 10x50mm dynabolts, holding down a plate, with another plate and loop welded to it so they can't be undone will do the trick.

Who do you have to piss off, to have three bikes stolen?

[jellywrestler]

Oh the irony

thieves not thiefs

not if you're a nigger and they thiefed off with it...

[Ocean1]

This: http://www.kiwibiker.co.nz/forums/sh...12#post1447012

[jellywrestler]

Two 10x50mm dynabolts, holding down a plate, with another plate and loop welded to it so they can't be undone will do the trick.

Who do you have to piss off, to have three bikes stolen?

is this suitable for wood and concrete floors?

[tigertim20]

Oh the irony

thieves not thiefs

call them what they are. cunts.

[Badfish]

Two 10x50mm dynabolts, holding down a plate, with another plate and loop welded to it so they can't be undone will do the trick.

Who do you have to piss off, to have three bikes stolen?

Thank you everyone.

lol who knows who i have pissed off, We keep to ourselves in the bike community we suspect someone who lives close (as my last bike i put a new exhaust and header on, on a saturday - gone that night, was quite loud) is watching or we were followed back from the track.
It is christchurch after all!

[haydes55]

Hello, The names Ryan.
Due to losing 3 bikes over the past year and a half we have come to realise we cannot be to secure.
My question is, What is the dynabolt that is widely used and thought highly of amongst the fellow NZ Bikers? what has worked well against theifs and what hasn't?

I will read the bike security threads when i have time, I did a quick search but nothing specifically dynabolt oirintated.

Thanks,
Ryan

This is what my flatmate has set up.


Basically bolted straight into the concrete, put the chain over the thread and screwed the nut over it and went nuts on the dirty welds so it wont come undone.

Hasn't been tested out but it's more secure than our mates other dirt bike beside it.

As a hint though, if you use a chain, a standard chain can be easily cut with a big enough bolt cutter, get as thick of a chain as you can. Also don't store bolt cutters or a grinder in your shed with the bike .... sounds common sense but I've seen that before

Whether bolted into concrete or set in concrete doesn't really matter as long as you make sure it's impossible to unscrew or rip it out. I'm not familiar with any brands but in my opinion branded deadbolts etc. Can be just over priced over glorified bolts. See what you can find in the local hardware shop.

[Drew]

is this suitable for wood and concrete floors?

"Dynabolt" is what we call masonry bolts in the building industry...For concrete and other masonry applications.

For timber floors, I would use coachbolts, or sheer bolts if I couldn't get under what I was bolting them down to.

[mossy1200]

http://www.google.co.nz/imgres?imgur...9QEwBA&dur=271

Ramset will have these type. Loctite them in and then drill the security screw inner away afterwards.

Or check this with pan head hex and also drill the hex round after. Stainless is best as hard to drill them away.


http://www.yanchor.com/BOLT.html

[jellywrestler]

"Dynabolt" is what we call masonry bolts in the building industry...For concrete and other masonry applications.

For timber floors, I would use coachbolts, or sheer bolts if I couldn't get under what I was bolting them down to.

http://www.ramset.com.au/Product/Det...Sleeve-Anchors


"designed for medium duty anchoring of timber and steel fixtures to concrete, brick or block."

you were right, just checking your product knowledge which as usual is shaky.

[skippa1]

Oh the irony

thieves not thiefs