BMW K100RS Project

**ducatilover** · 7th April 2015, 20:05

Oh my!!! That is bloody sexxxxxxxxxy

**JATZ** · 12th April 2015, 19:30

Originally Posted by BEAMER89

Man!! I take back my previous comment, that black looks sharp mate, awesome job. Almost gives me motivation to get stuck back into my BMW brick café/shed decoration project.

What he said Mossy

**mossy1200** · 25th April 2015, 17:11

Taken from garage started it up. Vrrrm. Back in Garage again. Ninja looked sad so gave it some penrite and took it for a ride.

**Arronduke** · 3rd May 2015, 17:20

Originally Posted by mossy1200

OK petrol in bike started and tested speedo. All good but need change it to 2 magnets on the settings. Its unlikely I was doing 100kph up my street in second gear on the CR at low rpm.
I think ill need install the silencer kit in the muffler as I think its louder than the ninja.

Here is the outside photos with a camera rather than phone.

Just catching up on this thread... WOW this machine looks outstanding, I spent 10min just looking at the pictures.
My only comment would be a rear seat pad would look cool. maybe its just that all the single seat bike I have one.

Hell still got several pages to go. Paint job is great, Black look awesome.

**HenryDorsetCase** · 11th May 2015, 22:41

Originally Posted by mossy1200

Taken from garage started it up. Vrrrm. Back in Garage again. Ninja looked sad so gave it some penrite and took it for a ride.

Someone stole the shock absorber from the left side.

AND PART OF THE SWINGARM TOO!!!!!

Looking good!

**Autech** · 21st May 2015, 09:20

Turns out this is my workmates old bike. He had it from '86 till 2004/5. He stuck the brembos and braided lines on it as well as the fork brace.

**mossy1200** · 21st May 2015, 14:22

Originally Posted by Autech

Turns out this is my workmates old bike. He had it from '86 till 2004/5. He stuck the brembos and braided lines on it as well as the fork brace.

I took fork brace off as it looked wrong with the guard.
The brembos are good but were very soft with the 13mm MC so I ordered a new 15mm master cylinder that was on the boxers and its mint braking now. They shared the same lever, slide and throttle tube assy and had same controls. Also put braided on the top lines and rear.

Its for sale if he would like it back.

**Autech** · 21st May 2015, 15:17

Originally Posted by mossy1200

I took fork brace off as it looked wrong with the guard.
The brembos are good but were very soft with the 13mm MC so I ordered a new 15mm master cylinder that was on the boxers and its mint braking now. They shared the same lever, slide and throttle tube assy and had same controls. Also put braided on the top lines and rear.

Its for sale if he would like it back.

Hahaha, he doesn't like what you did with it I am afraid, he's a bit of a BMW purest. His current Beemer is a 1958 R60 restored as best as he can to original condition.

Click image for larger version.

Name: DSCF0002.jpg
Views: 74
Size: 153.7 KB
ID: 312070

I like it though, looks bad arse!

**sidecar bob** · 21st May 2015, 16:36

Originally Posted by Autech

Hahaha, he doesn't like what you did with it I am afraid, he's a bit of a BMW purest. His current Beemer is a 1958 R60 restored as best as he can to original condition.

Id hardly say hes a purist, the /2 chassis did not come out with the 247 series engine