Results 1 to 10 of 10

Thread: Seating position?

  1. #1
    Join Date
    29th October 2007 - 21:19
    Bike
    Polini/Grc Rep
    Location
    Auckland
    Posts
    120

    Seating position?

    Well, just fell off and while sliding/peeling off skin on the tarmac I had a ponder; Am I sitting correctly on the bike?

    I read that on a full size bike, you shouldnt have any body weight pushing down on the handle bars.

    Is this true? and would it apply on a pocket bike?

    What is the correct seating position on a pocket bike?

    Cheers,
    Geoff.

  2. #2
    Join Date
    14th September 2007 - 16:34
    Bike
    '18 DRZ400SM
    Location
    Wellington
    Posts
    2,116
    Too cool for gear?
    "It would be spiteful, to put jellyfish in a trifle."
    \m/ o.o \m/

  3. #3
    Join Date
    9th January 2008 - 12:01
    Bike
    Custom Ag100
    Location
    The Tron
    Posts
    1,444
    More than likely your front tyre let go than a problem with weight distribution.

    Are you running Chinkas? if so invest in some Savas or Pmts before you loose too much skin

    On higher powered pocket bikes you have to have wt on the front to stop it lifting esp out of corners. Big bike rules don't apply as center of gravity is completely different.

    Also make sure you're wearing protective clothing and you shouldn't loose skin anyway.

    ciao

  4. #4
    Join Date
    29th October 2007 - 21:19
    Bike
    Polini/Grc Rep
    Location
    Auckland
    Posts
    120

    Too cool for school.

    Ok, so the rules of thumb are different (apart from saftey gear).

    I was wearing my helmet, and after the bike stalling and not running right I thought I would be going for a short ride.

    Thing is, I got it running mint, I got carried away and didnt go back for the knee/elbow pads etc which i should have.

    So Im not too cool (well nearly) for saftey gear, as every other time I wear it.

    The other thing as I was running different 'chingers' (wet weather) which seem to have quite a hard compound compared to my slicks+coupled with tyre pressure probably being too high.

    Also, new frame, brakes, carb etc etc

    Any rules of thumb for tyre pressure on pocket bikes?

  5. #5
    Join Date
    11th November 2007 - 14:07
    Bike
    2008 polini 910 4.2, 2008 suzuki drz125
    Location
    auckland nz
    Posts
    229
    when u go around a corner you should lean ur ass half on the seat and sretch ur knee out and try get ur knee on the ground and have ur other leg leaning out also hae it a pitty about the last race day...and how it rained on both day do you still ride your bike at turner car auctions?
    THE ONLY RULE IS, THERE'S NO RULES

  6. #6
    Join Date
    29th October 2007 - 21:19
    Bike
    Polini/Grc Rep
    Location
    Auckland
    Posts
    120
    Yeah I still ride round there, makes a good little test track 30sec from my house!

  7. #7
    Join Date
    11th November 2007 - 14:07
    Bike
    2008 polini 910 4.2, 2008 suzuki drz125
    Location
    auckland nz
    Posts
    229
    id like to take my bike around it
    THE ONLY RULE IS, THERE'S NO RULES

  8. #8
    Join Date
    4th January 2008 - 20:22
    Bike
    minimoto
    Location
    Christchurch
    Posts
    2
    I found out the hard way that the "big bike" rules don't really apply to little bikes. Little bike + wheel coming up off the ground + power band + no safety pads on = very sore for 2 weeks. Tar seal is like a cheese grater on your flesh.

    Hope you heal up alright

  9. #9
    Join Date
    29th October 2007 - 21:19
    Bike
    Polini/Grc Rep
    Location
    Auckland
    Posts
    120
    Yeah I'm healing up allrite, the missus is doing her final year training as a nurse.. So no need for expensive a&e!

  10. #10
    Join Date
    13th April 2007 - 17:09
    Bike
    18 Triumph Tiger 1050 Sport
    Location
    UK
    Posts
    3,802
    Mate, I am truly amazed by your story. I wasn't sure if you were being serious. I can see you are and I wish you the very best in getting fixed up.
    “PHEW.....JUST MADE IT............................. UP"

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •