Page 1 of 2 12 LastLast
Results 1 to 15 of 23

Thread: Turbo WR450 Motard

  1. #1
    Join Date
    25th January 2010 - 16:49
    Bike
    KLX250 Motard, XZ400 Cafe'
    Location
    Christchurch, New Zealand
    Posts
    29

    Turbo WR450 Motard

    I really miss my old Motard.

    It was a KLX 250 that had a big bore 400cc (ish) kit fitted to it by the previous owner. It went like stink and was a lot of fun.

    After Seeing this link on another post http://www.mpfab.com/wr250/ it has gotten my creative juices flowing. I had a hand in turbocharging my mates FZR 400 so this is within my grasp.

    Ok so Here's my plan.

    Purchase a road legal WR450 from my local Yamaha dealer. I should have that done by the end of next month.

    RGV250 17" wheels from bike wrecker. I'll have to machine up adapters to make them fit but should be ok.
    I could just buy a kit from Vroom.co.nz but they're a bit cost prohibitive.

    Front Brakes. RGV 250 Disc and stock caliper with custom made adapter. Or alternatively I may adapt a 4pot car caliper onto the bike. I've heard rumours of Nissan callipers working well, I have a pair of Series 4 RX7 4pot calipers in my stash of parts. I may use one of them.

    Rear brakes RGV Disc and stock caliper.

    Suspension
    This is where I will spend money on aftermarket parts.

    I plan to re-spring the front shocks myself with slightly stiffer and lower springs and use slightly thicker oil. (15wt istead of 5w)
    Rear probably similar deal stiffer and slightly lower spring.

    Engine
    I could spend a fortune going for a big bore kit but after the success we had with the Turbo FZR and seeing that very tidy Turbo-Tard WR250 on the previously mentiond link. I reckon this is the route to go.

    I have a CT9 Turbo off my old GT Starlet. Unless I can find a smaller turbo in good cond for the rite price I'll use what I've got.

    For the Turbo FZR build we got a steel shim made to lower compression. We simply bolted the head down with the shim sandwiched between 2 head gaskets. This lowered compression enough to avoid the huge detonation problems we were goin to have. That bike has just clicked over 1000km since the conversion without any problems.

    Dunno how this will work on a Thumper though. I'll try this metheod to start with as I'd like to avoid getting a custom piston made as I am definatly on a shoestring budget.

    I plan to make a pressure box enclosing the entire standard carby out of stainless. Jetting will be tricky but achievable. I'll keep the boost low (5-7psi above ambient) for the sake of reliability. The exhaust I'll fabricate also out of stainless. The Muffler I plan to use is a Boy racer spec dumpy stainless muffler meant to be fitted to a car. It has a 2" inlet (another unused item in the shed).

    Any suggestions would be much appreciated. I'm interested to know of any wheel/brake combo's that people have seen used on WR's.

    And before someone ask's no I'm not simply dreaming. I'm sourcing parts as I write this thread.

    To me building and modifying cars/bikes/boats is half the fun. The pleasure of driving/riding a one off you built is the other half.

    This bike should be heaps more fun than my 600 Bandit I've just sold. I can't wait to see the look on people's faces when they realise the monster I'm creating!!!

  2. #2
    Join Date
    26th May 2008 - 17:57
    Bike
    '05 Firestorm
    Location
    Browns Bay
    Posts
    302
    Good on ya, should be a bit of a laugh. I'd be a bit iffy about using the CT9 tho - a turbo designed for a 1300cc 4 pot might be a bit too big for a 450 single? Perhaps something you could find on a kei car might be a little more suited for this. Suzuki Capuccino had a 600cc 4 pot turbo, that kinda thing might be a bit easier to spin with a small engine.

  3. #3
    Join Date
    29th October 2007 - 00:44
    Bike
    F-18,Ginny and #66
    Location
    Sin City
    Posts
    5,026
    Blog Entries
    8
    Fantastic man. Go do it ! Will follow your progress with huge interest
    Don't Ride Faster Than Your Guardian Angel Can Fly !!!



    Hey Alan, Alan, Alan....

  4. #4
    Join Date
    5th February 2008 - 13:07
    Bike
    2006 Hyosung GT650R
    Location
    BOP
    Posts
    7,141
    I've begun on a similar project. I also wonder about smaller turbos off little diesels 2000cc ish - they should spool up nice and early.

    Suggest also, there might be less stress and expense by spacering below the cylinder rather than under the head.

    On the FZR how did you get on with your oil return? It's a bit of a mission to get the turbo outlet high enough above the oil level in the crankcase.


    Steve
    "I am a licenced motorcycle instructor, I agree with dangerousbastard, no point in repeating what he said."
    "read what Steve says. He's right."
    "What Steve said pretty much summed it up."
    "I did axactly as you said and it worked...!!"
    "Wow, Great advise there DB."
    WTB: Hyosung bikes or going or not.

  5. #5
    Join Date
    23rd August 2008 - 14:43
    Bike
    2007 XTX660
    Location
    Levin
    Posts
    162

    Thumbs up

    Quote Originally Posted by cheesemethod View Post
    Good on ya, should be a bit of a laugh. I'd be a bit iffy about using the CT9 tho - a turbo designed for a 1300cc 4 pot might be a bit too big for a 450 single? Perhaps something you could find on a kei car might be a little more suited for this. Suzuki Capuccino had a 600cc 4 pot turbo, that kinda thing might be a bit easier to spin with a small engine.
    You would get too much lag from a bigger turbo, keep it small and it will spin up much easier.

    this is a link from another site that turbo'd an XT660

    http://www.xt660.com/showthread.php?...ighlight=turbo

    I'm sure yours will be a fun ride. Good luck, and keep us updated
    All of this, all of this can be yours, Just give me what I want and no one gets hurt




  6. #6
    Join Date
    5th February 2008 - 13:07
    Bike
    2006 Hyosung GT650R
    Location
    BOP
    Posts
    7,141
    Theres a trick to reduce lag too, and thats to add a bypass flapper valve (similar to a 2strokes reed valve) on the inlet manifold, so to help the engine get past the boost transition point. While the turbo is off boost, there is quite a restriction on the inlet manifold - and the bypass valve allows direct access past the turbo.

    Steve
    "I am a licenced motorcycle instructor, I agree with dangerousbastard, no point in repeating what he said."
    "read what Steve says. He's right."
    "What Steve said pretty much summed it up."
    "I did axactly as you said and it worked...!!"
    "Wow, Great advise there DB."
    WTB: Hyosung bikes or going or not.

  7. #7
    Join Date
    25th January 2010 - 16:49
    Bike
    KLX250 Motard, XZ400 Cafe'
    Location
    Christchurch, New Zealand
    Posts
    29
    Thanks for the replies guys.

    Progress already. I may have found a suitable WR450 on TradeMe. I'll see how the bidding goes, If it goes for too much I'll simply keep looking.

  8. #8
    Join Date
    23rd April 2004 - 19:16
    Bike
    2010 DC Skate Shoes
    Location
    Roxby Downs, SA
    Posts
    7,089
    FWIW I'm pretty sure they are using the new WR250 which is fuel injected and also has much longer servicing intervals than the previous models. I'm guessing it's not in your budget but the 2009/2010 WR450 would be a much better starting point.
    KiwiBitcher
    where opinion holds more weight than fact.

    It's better to not pass and know that you could have than to pass and find out that you can't. Wait for the straight.

  9. #9
    Join Date
    25th January 2010 - 16:49
    Bike
    KLX250 Motard, XZ400 Cafe'
    Location
    Christchurch, New Zealand
    Posts
    29
    Replies to comments/questions
    Dangerous bastard & Cheesemetheod. Yeah I agree this turbo will be a bit big for what I need. I'm trying to track down a turbo off a Daihatsu charade or suzuki ignis but they aren't very common cars here in NZ.

    Dangerous bastard
    The CT9 comes out in several forms and trims. The one we used on the FZR was off a Toyota 2C Turbo diesel engine. It doesn't spool up too bad but it's still a bit laggy.

    The suggestion for the shim under the cylinder is a good one. To be completely honest it had never occured to me. We regularly make shims (as I described) when we turbo old engines like 4K Toyota's etc. Since this is a metheod we're used to it's the route we used on the FZR. but for the Tard the simple sollution of under the cylinder makes a lot of sense. I'll have to investigate this one.
    Last edited by Flying Spanner; 26th January 2010 at 13:08. Reason: because my spelling sux

  10. #10
    Join Date
    25th January 2010 - 16:49
    Bike
    KLX250 Motard, XZ400 Cafe'
    Location
    Christchurch, New Zealand
    Posts
    29
    Quote Originally Posted by R6_kid View Post
    FWIW I'm pretty sure they are using the new WR250 which is fuel injected and also has much longer servicing intervals than the previous models. I'm guessing it's not in your budget but the 2009/2010 WR450 would be a much better starting point.
    Yeah EFI makes these games much more simple. We fitted quad throttle body's off a 20Valve Toyota engine and a link computer to the FZR it made tuning much easier. As much as I wish I could afford a nice brand new EFI WR they cost about as much as my entire budget for this build. (I had a druel over a spankers WR450 this morning).

    I may end up adapting a single point injection setup of an early mazda or something. The pressure carby setup works fine for low boost (less than 15psi) and once the tuning hassles are dealt with doesn't work too bad.

  11. #11
    Join Date
    18th February 2009 - 14:44
    Bike
    Used to have a 1994 Kawasaki KLX250
    Location
    Nelson
    Posts
    28
    Hey just noticed you are in Nelson, a turbo WR450 would be mint to see roaming round the streets, will deffinately keep an eye on this.

  12. #12
    Join Date
    5th February 2008 - 13:07
    Bike
    2006 Hyosung GT650R
    Location
    BOP
    Posts
    7,141
    Quote Originally Posted by Flying Spanner View Post
    The CT9 comes out in several forms and trims. The one we used on the FZR was off a Toyota 2C Turbo diesel engine. It doesn't spool up too bad but it's still a bit laggy.
    I think the bypass valve would help with that. It allows the carbs to drink directly from atmosphere rather having to suck through a laggy off-boost turbo.

    How did you get on with your oil return line? I read lots of horror stories about that.

    Thats nearly the same turbo I'm using on my 650 project. They are pretty small..

    Model TBO2/22 (Garrett T25 - standard config)

    Compressor
    wheel trim 60
    Wheel Dia 1.46/1.89" (37/48mm)
    A/R 0.48
    Flow 21

    Turbine
    Wheel trim 57
    Wheel Dia. 1.39/1.85 (35.3/47mm)
    A/R 0.47
    Hose:2.0 inlet/2.0 outlet



    Steve
    "I am a licenced motorcycle instructor, I agree with dangerousbastard, no point in repeating what he said."
    "read what Steve says. He's right."
    "What Steve said pretty much summed it up."
    "I did axactly as you said and it worked...!!"
    "Wow, Great advise there DB."
    WTB: Hyosung bikes or going or not.

  13. #13
    Join Date
    1st March 2006 - 18:44
    Bike
    Tuono R , SD900
    Location
    AT HOME
    Posts
    758
    you might want to look at this then
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	DSC03554.JPG 
Views:	82 
Size:	104.4 KB 
ID:	194533   Click image for larger version. 

Name:	DSC03555.JPG 
Views:	85 
Size:	104.8 KB 
ID:	194534   Click image for larger version. 

Name:	DSC03556.JPG 
Views:	84 
Size:	94.2 KB 
ID:	194535  

  14. #14
    Join Date
    13th December 2008 - 18:22
    Bike
    Your mom
    Location
    Christchurch
    Posts
    3,901
    Put an external wastegate on it and a screamer pipe. Don't forget the vent to atmosphere blow off valve either.

  15. #15
    Join Date
    22nd January 2006 - 15:50
    Bike
    Honda CBR250RR, Sach's MADASS 125
    Location
    Christchurch
    Posts
    333
    Blog Entries
    3
    "Speed has never killed anyone!.... Suddenly becoming stationary, That's what gets you" - Jeremy Clarkson, Season 3 Topgear

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •