Log in

View Full Version : RVF400 Engines, covers, heads frames racers spare parts



lostinflyz
8th May 2010, 13:26
Hey everyone,

I've flogged off my 400 and now im trying to clear up some space in the shed for new stuff. Over the past few years i have stock piled plenty of spare parts so now they got to go.

Selling :

1.)Motor - Never used by me, was taken straight out of a race bike a few years ago, should all be there. Asking $500
2.) Covers - Some shiney Engine covers to make a rvf (of even better nc30) much cooler. Some minor scuffs and marks and one has been repaired but generally pretty good looking. asking $100
3.)Heads - Never been used, had valves reseated, ports and chamber cleaned . Some minor surface rust on a few of the valves but shouldn't be an issue. Should be perfectly good (were orginally nc30 but appear to have been modified to replicate all the 35 heads i have here. $100

I have a couple of frames (both nc35)
a nc30 and 35 swingarm (35 is about 80% polished).
hubs and all sorts are here.
I have a full stock exhaust in reasonable condiiton (has gone down once somewhere).
Full wiring loom. (nc35 i think)
another motor in bits (some parts missing)

Anything along those lines please let me know, i want it gone so make me an offer. The more you buy the cheaper it gets to. Can bring to chch or invercargill or in between, or may be able to help out getting it elsewhere.

My flash new marchesini magnesium rear rim (5.5) is still here too and i have a modified rear hub (untested, but took around .5kg out of it, and should be good to go) as well if anyone is interested, but not cheap.

couple of photos of various bits.

HenryDorsetCase
8th May 2010, 17:29
I need a wiring loom and maybe a CDI and (wont know till I get a loom that works....) Would like a set of NC30 forks, and some front discs.

lostinflyz
8th May 2010, 18:02
i have a loom in chch. ill grab it next week and figure out whether its a 30 or 35 one. No CDI's. No forks left and i have a front disc but its pretty skinny. You can have it if you like but i took it off cause of sizeable brake fade at some tracks.

Crasherfromwayback
8th May 2010, 18:10
I need a wiring loom and maybe a CDI and (wont know till I get a loom that works....) Would like a set of NC30 forks, and some front discs.

Think I can help you out there mate! Got another complete bike for the girlie, and will have quite a few spare bits.

Joe Blogs
9th May 2010, 17:55
Hey, would the heads fit a NC35? how different are they?

Cheers
JB

lostinflyz
10th May 2010, 20:21
yea they will bolt straight on. The 30 heads have a much higher flow figure, but poor flow. these have been tweaked quite a bit so should be as good if not better than stock 30 heads. If you want jesse i have about 90% of a motor (everything bar rods and pistons) hanging out there that you can have for a couple of boxes of beer.

Joe Blogs
11th May 2010, 16:01
Its a deal, when will you next be in chch? Will you be at King Of Levels Round 1 on the 17th July? Or if u are up before then you could leave it at Daniels, I'm sure he wouldnt mind. Cheers man

JB

lostinflyz
13th May 2010, 22:32
umm not sure. Bike building at the moment so as soon as i can get that done itll be on track. hopefully be in chch next weekend to see what a floppy floppy motard with clip ons is like.