Ninja 250R Custom mods

[crash99]

Show us your ninja 250 whatever year with any mods

[crash99]

225955225956225957225958225959225960

Made by cycleworks in Lower Hutt :yes:

[Gibbo1]

shit how loud is that? Have you re jetted the bike as well?

[mikemike104]

1989 Gpx250f ex usa so speedo in miles now done 25500

Repaint White by previous owner, I'v had it since this March and the paints getting shabby so it was not a professional job.

I have had installed a ex250j model rear shock, feels lots better than the one that was in it when I got it.

Has Yoshi exhaust, unsure if its just a can but suspect its the full length. Quite loud.

Aftermarket flush mount front indicators to replace stick out stalks that look ugly from factory. Jap rear light, coloured red with orange instead red all round.

Pirelli Sport Demons front & rear.

Planning some nice new brake pads all round soon, any good ideas on pads ?

[SMOKEU]

Put a turbo on it.

[mikemike104]

Put a turbo on it.

Could just take the money I'd spend and buy a nicer bike... I reckon that's probably what I'll do.

[SMOKEU]

Could just take the money I'd spend and buy a nicer bike... I reckon that's probably what I'll do.

Get a litre bike.

[Genie]

Well here's my little Black Beast. Must say that they look good in white!

First pic, only had the tinted bubble screen on, what a difference that did make. Surprising.

Second pic was just after the boys fitted the new noise maker....lovin it!

Got the boys to tidy up that spade on the rear, fitted a single seat cowl thingy whatsit and fitted some new tyres...just loving this bike, don't care what I spend on it, it's mine and it's not going anywhere.

Once I've finished titivating this one I'll just buy me another new one to play with/on. Two is always better then one, and then I may even go to three!

[mikemike104]

Very nice :yes:

[steve_t]

Two is always better then one, and then I may even go to three!

Have u been hanging out with steelphoenix? :innocent::sunny:

[crash99]

Genie where did you get your rear seat cowl? been looking for one for mine for a while and couldn't find one in NZ? The new shorty is bloody loud, guy who made it said it didn't need to be re jetted but whenever i throttle off in second third or fourth it backfires a little :blink: so... still sounds wicked :yes::gob:

[sil3nt]

Genie where did you get your rear seat cowl? been looking for one for mine for a while and couldn't find one in NZ? The new shorty is bloody loud, guy who made it said it didn't need to be re jetted but whenever i throttle off in second third or fourth it backfires a little :blink: so... still sounds wicked :yes::gob:You need to rejet....

http://forums.ninja250.org/viewtopic.php?t=80912&highlight=rejet&sid=ca64280e553f5ad4d55f1caf3560f8ea

[Genie]

Genie where did you get your rear seat cowl? been looking for one for mine for a while and couldn't find one in NZ? The new shorty is bloody loud, guy who made it said it didn't need to be re jetted but whenever i throttle off in second third or fourth it backfires a little :blink: so... still sounds wicked :yes::gob:

Got the seat cowl through Filco's here in Nelson...give them a call 03 5472420, they can get them in other colours too and they're fast - two days!!!

Definately go for the rejetting thing, some needles need to be adjusted and the bike will need a wee tune-up, apparently doesn't matter if it's not done straight away, mine's not getting done until 12000k service but it does need to be done. I bet yours is loud, mine is too!!!:yes:

[2wheeldrifter]

Well here's my little Black Beast. Must say that they look good in white!

First pic, only had the tinted bubble screen on, what a difference that did make. Surprising.

Second pic was just after the boys fitted the new noise maker....lovin it!

Got the boys to tidy up that spade on the rear, fitted a single seat cowl thingy whatsit and fitted some new tyres...just loving this bike, don't care what I spend on it, it's mine and it's not going anywhere.

Once I've finished titivating this one I'll just buy me another new one to play with/on. Two is always better then one, and then I may even go to three!

Looking good Genie... did not realize how much you had tinkered with it, all you need is Crash99's tail tidy job done?

Need a hand with your titivating.... just sing out :)

Crash99 yep rear seat cowl would finsih yours of nicely... love the little muffler, tidy job. :yes:

[Genie]

Looking good Genie... did not realize how much you had tinkered with it, all you need is Crash99's tail tidy job done?

Need a hand with your titivating.... just sing out :)

Crash99 yep rear seat cowl would finsih yours of nicely... love the little muffler, tidy job. :yes:

Yeah, you're not wrong on the tail tidy...when can you get here to do it? :lol:

[2wheeldrifter]

Yeah, you're not wrong on the tail tidy...when can you get here to do it? :lol:

Oh you tease, would love to play with your rear end.... remember I ride a Ducati, so could take me a few months to get down there :yes:

[Kermit250]

We just sold our lil 08 250r, I'll post pics soon.

Some bloke in Tauranga has it now

Mods I did to it:
Exhaust
stage 2 jet kit
airbox opened up
tail tidy (not just a cut, but proper tidy)
seat cowl
rear wheel hugger (imported from UK)
removed reflectors
heated hand grips
digital temp guage
monster energy decal kit
green wheel stripes

If you now own our old bike, PM me, wouldn't mind seeing how its going!

[crash99]

Where did you get the jet kit from??? I'd be interested because I've been looking at ones on dynojet website and they say they don't ship to NZ???:innocent:

[R6_kid]

Where did you get the jet kit from??? I'd be interested because I've been looking at ones on dynojet website and they say they don't ship to NZ???:innocent:

Thats because they have agents in NZ. AMPS and North Harbour Yamaha spring to mind.