PDA

View Full Version : Vapour issues


Woodman
27th December 2011, 14:54
Just went down to gas up for aa assault on the Molesworth and noticed that my speedo would only read to 21km/h. Odd I mused so watched it more closer and it goes all over the show and occaisionally flashes (I think) the correct speed, but really only gets to 21.6 or so. Everything else works e.g. shiftlight,temp,clock,tacho etc.

Checked all the connections and the pick up etc and the only thing I found was the speed pickup wire is a wee bit crushed where it shares an eyelet with the throttle cables. All the settings are still the same and it was working fine the other day.

Just read the manual and it says that the cables need to be real good and not crushed etc so possibly this post is pointless, but still willing to hear and share any others experiences.
Box'a'bits
27th December 2011, 15:13
Noticed that my speedo would only read to 21km/h. Odd I mused so watched it more closer and it goes all over the show and occaisionally flashes (I think) the correct speed, but really only gets to 21.6 or so. Everything else works e.g. shiftlight,temp,clock,tacho etc.

Checked all the connections and the pick up etc and the only thing I found was the speed pickup wire is a wee bit crushed where it shares an eyelet with the throttle cables. All the settings are still the same and it was working fine the other day.

Just read the manual and it says that the cables need to be real good and not crushed etc so possibly this post is pointless, but still willing to hear and share any others experiences.
Check how the speedo head/magnet is mounted. Mine deteriorated, with the magnet becoming less strong, & the disc floating. I've remounted things into a different configuration & it's all good now.

Alternatively get a new cable.
NordieBoy
27th December 2011, 20:24
I use a neo magnet (duh) just stuck to the disc and the pickup is 2-3cm away with no issues.
If you still have a problem then it's probably the wiring...

I'll bring some magnets tomorrow...
Taz
27th December 2011, 20:27
It's a klr. Do they go faster? :crazy:









Well someone had to say it.
Woodman
27th December 2011, 20:29
I use a neo magnet (duh) just stuck to the disc and the pickup is 2-3cm away with no issues.
If you still have a problem then it's probably the wiring...

I'll bring some magnets tomorrow...

The magnet is part of one of the rotor bolts. I tried spacing it out so it was closer to the pickup, but alas to no avail. Hopefully its just the magnet, otherwise I will need a new pickup and wire.
NordieBoy
27th December 2011, 21:39
One test is to wave a magnet back and forth by the pickup and see what happens.
Box'a'bits
28th December 2011, 06:59
One test is to wave a magnet back and forth by the pickup and see what happens.
Nah, its obviously working at least to come extent, because he's getting 21kph out of it. So strength of signal or a disruption are the issues.
NordieBoy
28th December 2011, 19:16
Nah, its obviously working at least to come extent, because he's getting 21kph out of it. So strength of signal or a disruption are the issues.

His odo is good though...
The rev counter was playing up a bit too.
Woodman
28th December 2011, 21:20
His odo is good though...
The rev counter was playing up a bit too.

Yea the Odo is fine which means it must be something in the unit itself which is a worry, i wonder if resetting it will help?

The tacho is fine, I was looking at the trip meter thinking it was the rev counter:facepalm:
Padmei
29th December 2011, 07:50
I lost my bloody magnet meaning my speedo wasn't working. I had my GPS howver you realise how much you rely on the trip meter for fuel levels.
Waihou Thumper
29th December 2011, 09:50
I lost my bloody magnet meaning my speedo wasn't working. I had my GPS howver you realise how much you rely on the trip meter for fuel levels.

​Do you reset your tripmeter on the GPS too? Bigger screen, easier to see and a lot more accurate between fuel stops distance wise.
I got a WOF with GPS working only as the rules allow for this (apparently)
JATZ
29th December 2011, 11:08
Yea the Odo is fine which means it must be something in the unit itself which is a worry, i wonder if resetting it will help?

The tacho is fine, I was looking at the trip meter thinking it was the rev counter:facepalm:

My speedo went all to hell just before the last Maunga trip, I re-set it but it made no difference, had to re calibrate again and added some more to the tyre circ. to give a truer reading. It's about .7k's out at 100k's when measured with the GPS.
Buddha#81
29th December 2011, 22:14
Anyone know where I can get a replacement temp sender for mine? I accidently put 12v through mine and open circuited it :angry:
Padmei
30th December 2011, 08:01
Anyone know where I can get a replacement temp sender for mine? I accidently put 12v through mine and open circuited it :angry:

Email the dude that sells them on trademe. I got a drz one for the bmw & he said he had a temp sensor that could swap or buy. He's a good sort.
Woodman
1st January 2012, 12:59
It works proper again.

Pushed the reset button on the back and now it works.:brick:
Padmei
1st January 2012, 13:55
It works proper again.

Pushed the reset button on the back and now it works.:brick:

And your bike has less k's on it now!
Woodman
1st January 2012, 15:57
And your bike has less k's on it now!

No, it never changed any settings at alllincluding shift light, clock etc etc so the odo is the same. Pretty sure you can't change the odo at all, but could be wrong or mis-informed.
Box'a'bits
1st January 2012, 16:32
No, it never changed any settings at alllincluding shift light, clock etc etc so the odo is the same. Pretty sure you can't change the odo at all, but could be wrong or mis-informed.
You can if you know how to do it. I used this to add mileage when I swapped from the old spedo to the new one.