Anyone have a zzr250 ex-1994 service manual?

[ir0nslash]

wrong location admin please delet

[ir0nslash]

anyone have a Kawasaki zzr 250 ex 1994 service manual ??

just interested to go threw it , as my bike most likely needs a full overhaul ,

just brought it month ago , took it out to a bike shop to get the air valve full unit change as the rubber was cracking the guy noticed front seals are leaking , been taped with like electrical tape were dust covers are , abit weird , guy said hes never seen a fix like that before , I said the last owner told me he got it serviced at some shop near him , but just that alone and clutch lever ball end is snapped off and he said both those things wouldn't pass a warrant , so someones been doing the dodgy warrant im expecting and the shiz he told me hes done to it hasn't actually been done to it ..... so need to give it a full monty before I run into trouble ..... any help be greatful ....

bike shope said front seals etc for around $250-300 and full service be like $600-700 , said something in the motor at around 44000kz needs to be reset as they start closing after time and seizes the motor ??
apart from trying to reset it , ild prefer trying to fix everything myself as im broke apprentice
newbie needing advice cheerz

[Akzle]

a) pirate that shit
b) stop being a cheap cunt and go and buy one.

[Laava]

If I was you IRonsLash.! I would search on here for people in auckland who have the same bike as you and ask them directly.
Axehole can help you if you are wanting to mate with goats, or keep track of fuel economy on redundant cars, that's about it really.

[Akzle]

If I was you IRonsLash.! I would search on here for people in auckland who have the same bike as you and ask them directly.
Axehole can help you if you are wanting to mate with goats, or keep track of fuel economy on redundant cars, that's about it really.

hey, remind me again if the vehicle you drive causes cancer or not...


(eat a dick you old white git)

[Gremlin]

Try this: https://mega.nz/#!aU1jhS7D!RpQ14-fNBrLJ8wUeHOuHV2h1siZk_aVhH4g-J1Pko3Y

[husaberg]

Yeah don't mind axhole, hes like the village idiot only the village he comes from is Auckland and nobody likes him.
He can't be the court Jester because he's not funny and he already has a persecution complex.
Butt he''s your girl if you need advice on keeping goats.

[Laava]

hey, remind me again if the vehicle you drive causes cancer or not...


(eat a dick you old white git)

Oh dear, touched a raw nerve there! Poor diddums. Never mind, you could always just fuck off to a forum that is relevant to you?

[Akzle]

Oh dear, touched a raw nerve there! Poor diddums. Never mind, you could always just fuck off to a forum that is relevant to you?

ill take that as a yes. You cause cancer :niceone: douche.

[Akzle]

http://www.doc.govt.nz/pagefiles/17650/tane-mahuta-223.jpg


Yeah don't mind axhole, hes like the village idiot only the village he comes from is Auckland and nobody likes him.
He can't be the court Jester because he's not funny and he already has a persecution complex.
Butt he''s your girl if you need advice on keeping goats.
:tugger:

[SVboy]

http://www.doc.govt.nz/pagefiles/17650/tane-mahuta-223.jpg


:tugger: and the child rapist emerges from his coma. Fuck off axle.

[ir0nslash]

im so confused what just happened to my thread haha ....

[FJRider]

Yeah don't mind axhole, hes like the village idiot only the village he comes from is Auckland and nobody likes him.
He can't be the court Jester because he's not funny and he already has a persecution complex.
Butt he''s your girl if you need advice on fucking goats.

There ... fixed it for you ...




He is the proverbial village idiot ... well he would be ... if we could find a village that will admit HE is one of them.








No luck ... so far ...

[Akzle]

im so confused what just happened to my thread haha ....

kb .

[Akzle]

and the child rapist emerges from his coma. Fuck off axle.

fuck i want to punch your children.

[ir0nslash]

Try this: https://mega.nz/#!aU1jhS7D!RpQ14-fNBrLJ8wUeHOuHV2h1siZk_aVhH4g-J1Pko3Y

thanks Gremlin ....

[SVboy]

fuck i want to punch your children.

I doubt that reply surprises anybody on KB. Still, it's a step above threatening to rape them, you peadophiliac cunt.

[Akzle]

I doubt that reply surprises anybody on KB. Still, it's a step above threatening to rape them, you peadophiliac cunt.

when did i say id rape anyones children?

[SVboy]

fuck i want to punch your children.


when did i say id rape anyones children?

Don't pretend the P completely fried your brain tosser. A while back you didn't like one of my replies, so you threatened to rape my kids. At that point you became my KB bitch. Don't like it? Then fuck off.

[Akzle]

Don't like it? Then fuck off.

or... you.

[husaberg]

Don't pretend the P completely fried your brain tosser. A while back you didn't like one of my replies, so you threatened to rape my kids. At that point you became my KB bitch. Don't like it? Then fuck off.

I sincerely doubt he does P only goats and trolling.
He threatening to rape your kids as well? You would think he would be a little more original with his troll threats.
He posts pics of trees for me now after he got a little bit of his own unwanted attention back, funny enough I see the trees and just think to myself, Fool why doesn't he just Leave.

[Delerium]

you might be able to download from scribd or another site.

[ducatilover]

Way to ruin a thread dick heads

The thing that needs resetting is the valve clearances, and they won't make your motor seize
Fork seals are pretty easy to do yourself with a manual and a little know how with your spanners :2thumbsup
Valve clearances are easy for a reasonably educated DIY chap, you have shims, so you will need to replace them (chances are your exhaust ones are needing replacement) many bike shops will do shims and swap them with your old ones for $8 each or so
You will want good measuring equipment and ideally a 1/4 drive torque wrench for your cam caps

[SVboy]

Fair call, my apologies to the OP.

[husaberg]

Way to ruin a thread dick heads



Fair enough...... I think Grumph has done a few engines for the 250 class they have down in CHCH
He may have access to a manual if Gremlins link doesn't work out.

[ir0nslash]

The thing that needs resetting is the valve clearances, and they won't make your motor seize
Valve clearances are easy for a reasonably educated DIY chap, you have shims, so you will need to replace them (chances are your exhaust ones are needing replacement) many bike shops will do shims and swap them with your old ones for $8 each or so
You will want good measuring equipment and ideally a 1/4 drive torque wrench for your cam caps


thanks a lot , ducati , really big help cheerz .... and yea grems manual worked and stoked to get it ... that's dudes

[husaberg]

thanks a lot , ducati , really big help cheerz .... and yea grems manual worked and stoked to get it ... that's dudes

There is a page thread for manuals on KB might pay to add it in.
http://www.kiwibiker.co.nz/forums/showthread.php/10556-Lotsa-manuals-online


like that time i repped someone every day for 3 months...

Pardon bitch.....Not my fault you didn't notice.

silence is consent mods.


uhhh, actually in NZ silence IS consent.

[Akzle]

after he got a little bit of his own unwanted attention back,

like that time i repped someone every day for 3 months...
O. Wait on... :laugh: douche.