You couldn't ask him for me would ya? I could really do with the four-prongy thing one.Originally Posted by SARGE
or .. you can just get ahold of that SARGE guy .. he may have one on the tool truck ....
Steve
Double shot!!
You couldn't ask him for me would ya? I could really do with the four-prongy thing one.or .. you can just get ahold of that SARGE guy .. he may have one on the tool truck ....
Steve
"I am a licenced motorcycle instructor, I agree with dangerousbastard, no point in repeating what he said."
"read what Steve says. He's right."
"What Steve said pretty much summed it up."
"I did axactly as you said and it worked...!!"
"Wow, Great advise there DB."
WTB: Hyosung bikes or going or not.
LOOK.. ZOMBIES!
i have a couple on the truck .. ring me friday and i will see what size i have and what size i can get..
pm'd the #
Retirement with a cause
What do you have Sarge , OTC shit or what ????
Double shot!!
Bump, still didn't find one of these tools. Anyone got any suggestions? I tried to bash it around with the pin punch, but it didn't budge. Big rattle gun time?
Steve
"I am a licenced motorcycle instructor, I agree with dangerousbastard, no point in repeating what he said."
"read what Steve says. He's right."
"What Steve said pretty much summed it up."
"I did axactly as you said and it worked...!!"
"Wow, Great advise there DB."
WTB: Hyosung bikes or going or not.
LOOK.. ZOMBIES!
no .. T&E brand out of the States
Sorry DB.. i looked through all my stuff and finally went to Haldanes to look at what they used .. seems they just take a grinder to a socket
gee wizzz
Steve. The tool you need looks a lot like the tool used to undoo the locknut on an angle grinder---only bigger.
Trying to describe it --take a 28mm spanner and weld 2 6mm bolts on the two"forks" of the spanner hopefully paints a picture of what it looks like
To see a life newly created.To watch it grow and prosper. Isn't that the greatest gift a human being can be given?
His Excellency
Honda clutch hub nut removing tool might fit. (same design, and very close in measurement)
Visit ya local Honda w/shop.
(I got one in my toolbox, but I don't loan any tools. Once bitten twice shy).
Double shot!!
Ok thanks fellas. Looks like I'll hack something up from scratch, as I'll be using it occasionally it seems. Greatly appreciate your help also Sarge - if you don't have it, then probably there aint one.
Cheers,
Steve
"I am a licenced motorcycle instructor, I agree with dangerousbastard, no point in repeating what he said."
"read what Steve says. He's right."
"What Steve said pretty much summed it up."
"I did axactly as you said and it worked...!!"
"Wow, Great advise there DB."
WTB: Hyosung bikes or going or not.
Double shot!!
Pfft, I should done the socket thing to begin with instead of wasting all that time.. Was a piece of piss. Ten minutes on the grinder and I have a custom tool, and 60 seconds later the nut is off.
Steve
"I am a licenced motorcycle instructor, I agree with dangerousbastard, no point in repeating what he said."
"read what Steve says. He's right."
"What Steve said pretty much summed it up."
"I did axactly as you said and it worked...!!"
"Wow, Great advise there DB."
WTB: Hyosung bikes or going or not.
Forum whore
See - sometimes there is good advice on KB!!!!
Double shot!!
Weird innit..
I'm amazed that, a.) it fit so well on the first try, and b.) that it came off with so little effort after the punch wouldn't budge it, and c.) I didn't break the tool..
Steve
"I am a licenced motorcycle instructor, I agree with dangerousbastard, no point in repeating what he said."
"read what Steve says. He's right."
"What Steve said pretty much summed it up."
"I did axactly as you said and it worked...!!"
"Wow, Great advise there DB."
WTB: Hyosung bikes or going or not.
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote
Bookmarks