ducatilover's squidtastic pile of crap

[ducatilover]

Have you seen this thread:

http://www.customfighters.com/forums...ad.php?t=24146

Pics on this page:
http://www.customfighters.com/forums...=24146&page=61

?

It's AMAZING.

Yeah mate, it's a beautiful bike!!!!! I've been trawling the forum a hell of a lot, there's a few ZZR's in there too.

[ducatilover]

Bling in the mail today

[Parlane]

Bling in the mail today

Aw, they look good. But I quite liked the old forks, they had an artistic twist to them :P

[ducatilover]

Aw, they lookg ood. But I quite liked the old forks, they ahd an artistic twist to them :P

Don't worry, I'll ruin these ones fast enough

[Dodgy_Matt]

Hit dude, now you are gonna have to buy some clip on bars... that will kill you.

I just sold a set that would have fit your new forks for like $40...

[scumdog]

Don't worry, I'll ruin these ones fast enough

Prop them up on the kerb and get the next garbage truck to run over them and bend them.
Save you the effort of fluffing around fitting them to the bike just to bend them!!

(I'm just chock full of such handy ideas)

[ducatilover]

Prop them up on the kerb and get the next garbage truck to run over them and bend them.
Save you the effort of fluffing around fitting them to the bike just to bend them!!

(I'm just chock full of such handy ideas)

You, sir, have saved me another hole in my Qmoto gear!

Hit dude, now you are gonna have to buy some clip on bars... that will kill you.

I just sold a set that would have fit your new forks for like $40...

It has the bar clamps on it already and the spare/straight ZZR ones bolt straight in



Forks go straight on, use the top nut from the ZZR and ZZR bearings. Shaft size is the same and the top bearing is the same, the bottom is a wee bit bigger, so I'll buy a set of ZZR bearings and she'll be sorted.

Axle from the spare ZZR slides straight in, am missing the tool to take the front wheel off the super-custom forks to get at the speedo drive though Doesn't look like it'll need spacers though.

Will have to modify/butcher the steering stop and the lock-thingy on the headstock.

I was going to make my seat today, but, I have lost my vinyl! I have gone through the garage and multiple cigarettes, yet cannot find the damn stuff. What a piss off.

I may get around to shortening the exhaust cans though

[ducatilover]

Pic whoring. Painted the bar clamps and attacked the frame with the grinder so there are so clearance issues with the ZXR clamps

[ducatilover]

Pulled the rear shock apart today, forgot to take pics
Will paint the shaft (haha) black again and the spring red.
Cleaned up the inside of the frame and the shock linkages because whomever had the bike before couldn't clean to save themselves.
Will rip the grease nipples (hehe) off tomorrow and clean 'em up too.

[DrunkenMistake]

I like your race stand.... How much?

[ducatilover]

I like your race stand.... How much?

Give me a reach around and call me Sparky for it?

[scumdog]

Pulled the rear shock apart today, forgot to take pics
Will paint the shaft (haha) black again and the spring red.
Cleaned up the inside of the frame and the shock linkages because whomever had the bike before couldn't clean to save themselves.
Will rip the grease nipples (hehe) off tomorrow and clean 'em up too.

Fuck that shit - where's the chrome and tassles, the stuff that counts!



(Wait 'til I'm sober, it'll get worse!)

[ducatilover]

Fuck that shit - where's the chrome and tassles, the stuff that counts!



(Wait 'til I'm sober, it'll get worse!)

I'll get some off the little girl's bike down the road

Pass me a drink you southern twit.

[Parlane]

I'll get some off the little girl's bike down the road

Pass me a drink you southern twit.

[ducatilover]