Seafoam ZXR 250

[Spoonrider]

Hi guys,

So I have some really weird hesitation issues with my ZXR 250 between 6 - 8k rpm. I have some seafoam to try in it as I think it did sit for quite a while before I bought it. I am going to try it in the tank but also want to try the induction into a vacuum hose while running method, then leave it for 10 -15 mins and then run it. To do this would I just use the main gas line from the tank or the small vacuum hose that comes off the tank?

They say it needs to be a vacuum line that feeds all of the carbs...

[Sable]

You're a retard.

[Spoonrider]

Sweet, thanks for the constructive feedback man.

[Sable]

Sweet, thanks for the constructive feedback man.

No worries, any time

[willytheekid]

Sweet, thanks for the constructive feedback man.

Yeah...get used too that around here mate.

Seafoam is a very good product, check out there site, every question you may have is answered.
http://www.seafoamsales.com/gasoline-engine-faqs.html

...and yes, you can do the vacume method safely (pour the seafoam into a container and just let the vacume hose suck it out slowly)

Rule of thumb is 1/3 of the seafoam used for the tank, 1/3 for the engine oil and 1/3 for the main vacume line ...then a flush out run (don't thrash it!...just a gentle cruise)...remember to change your oil sooner than normal if treating the engine (don't have to do it straight away tho...but it does effect the oils useful life span)

[bungbung]

Describe the hesitation and how it occurs. Does it hesitate in the same place if you gently wind on the gas compared with cracking it open?
The zxr250 is very sensitive to vacuum leaks, and now they're 20 years old the rubber can be in poor shape.

[Spoonrider]

Thanks for the replies guys.

So the vacuum line is the smaller tube coming from the petcock?

The hesitation is between 6 - 8k as mentioned, I can feel the bike holding back at low throttle, if I give it more throttle I can push through it. When the hesitation is occuring the exhaust sound is noticably different. Kinda hard to explain, the other thing that I notice when this happens is that when I pull up to a stop at lights or whatever the idle goes low like it is going to stall.

[ducatilover]

It's lean on the transition to the main jet.
Is it running a standard air filter and muffler?
If it's running aftermarket filter and/or muffler you'll want to go up in jet sizes and needle height.
Or your float heights are on the piss

[Sable]

Needles could be worn. Disassembly, float height adjustment and thorough cleaning then go from there. Still, stupid fucking question

[FJRider]

Sweet, thanks for the constructive feedback man.

If you don't know what is actually the issue causing the hesitation, how do you know your intended "fix" will actually help ... let alone FIX the problem. Especially when you need to ask how to do it.

Retard ... is probably being quite polite ...

[Spoonrider]

Someone suggested that the carbs, or in particular, the jets may be gummed up. They said I may as well try Seafoam before taking everything apart (or getting a professional to do that) to see if it helps. I was going to add some to the gas in my tank and as suggested, I was going to try some down the vacuum hose too and just wanted to make sure I was using the right hose.

For a bike of this age and value, is it worth getting someone to take it apart, check the needles and do the right adjustments?
Is it even possible to get new needles for these bikes anymore?

Everyone starts out as a newbie at some point and needs a little advice from time to time...

Thanks anyway to the people that have replied me constructively.

[willytheekid]

Someone suggested that the carbs, or in particular, the jets may be gummed up. They said I may as well try Seafoam before taking everything apart (or getting a professional to do that) to see if it helps. I was going to add some to the gas in my tank and as suggested, I was going to try some down the vacuum hose too and just wanted to make sure I was using the right hose.

For a bike of this age and value, is it worth getting someone to take it apart, check the needles and do the right adjustments?
Is it even possible to get new needles for these bikes anymore?

Everyone starts out as a newbie at some point and needs a little advice from time to time...

Thanks anyway to the people that have replied me constructively.

Don't worry about the mean comments mate. (I thought it was a reasonable question and request for advice...nothing to be attacked over or called names about?)

Seafoam IS a good place to start
If the bike has indeed been sitting for a long time it may well just need a clean out/flush of the carbs, as it could be somthing simple like a partially blocked jet or sticky floats etc.(which seafoam should fix...as this is what it is designed to do)

However-
If you treat the bike with seafoam and the problem is still there, THEN you can move onto the next action of getting greasy and throwing some tools at it. (Or taking it to a mechanic if your not confident in doing it yourself)
Check the emulsion tubes are not blocked or that any of the rubber tubes and seals are not perishing...could be an air leak or blockage, or even crud in the fuel tank/fuel tap etc, but a good place to start would be popping the plugs out to give you a sign of what is happening in each cylinder in regards to air fuel mix (read the plugs..what colour are they-grey, black, brown or melted! lol)...always start with the basics before ripping things to bits.

Treating the bike with seafoam will not hurt in the least, and may just fix the issue with minimal cost and effort involved...so why not start there
If it dosn't work, it hasn't cost you much money or time and the bike still benefits from getting a good flush out after sitting for so long.(You may want to put new plugs in as well and give it an oil change not long after the seafoam clean out )

Best of luck and I hope you get the problem sorted

[Spoonrider]

Thanks Willytheekid.

I take it that if I take the vacuum hose off the petcock (the small hose) in order to introduce the Seafoam, that I will need to turn the petcock to the prime setting to allow the gas to flow freely?

[bogan]

Petcock vac lines are often only connected to one cylinder/carb. But yes, you would need to turn it to prime. I'm not quite sure why you would want to put it through a vac hose anyway? If its varnish on the main jets adding it to the fuel should clear it up. If not, the carbs will need taking apart, and unless you've changed the exhaust or intake, start with the float heights.

[Coolz]

Thanks Willytheekid.

I take it that if I take the vacuum hose off the petcock (the small hose) in order to introduce the Seafoam, that I will need to turn the petcock to the prime setting to allow the gas to flow freely?

That sounds about right to me. I mentioned Seafoam on here once and they all jumped down my throat also. Seafoam doesn't seem that well known here but is highly recommended on American forums. Good luck.