And reading a bunch of your other posts / threads, I rekon you're an honorary dorklander yourself. You welcome.Originally Posted by Akzle
Hardsnore Biker
And reading a bunch of your other posts / threads, I rekon you're an honorary dorklander yourself. You welcome.
Honda Lover
could always get another compressed air tank to fill , my m8 converted a old lpg one to fil with air
plastic fabricator/welder here if you need a hand ! will work for beer/bourbon/booze
come ride the southern roads www.southernrider.co.nz
Cyborg Biker
Nail guns use bugger all air... some you can set others are set via the presure you set on the compressor...
I would check your cyclinder and drain it... most common thing people forget to do...
Depending on the gun may need a bit of oil... exaple most brad guns a couple of drops in the air hose connector before you use it for the day... some guns have an oiler nipple or something...
Hardcore Biker
Choice love nail guns.
Nailed myself to a frame with one once.
Coming down cause it was raining,had gun in one hand an lowering myself with the other when I slipped an bumped the gun into the frame at the same time as I squeezed the trigger.
Through the corner of the frame an pinned me to a nog by my index finger.
Good thing I had my side cutters in my belt because my mates weren't being very helpfull,,,,,funny pricks aye.
Learn't a couple of things about site safety that day
Highway Biker
I like my Paslode guns got 2 of them. 1 for nails and 1 for brads.
On decks I use Paslode Deckfast nails that have groves and a round head. On the gun I use the No-Mar tip that has a rubber block on the end that leave no mark on the decking.
Forum whore
Yeah ok but i don't think you can buy or rent Ramset type equipment without the ticket.
it's not a bad thing till you throw a KLR into the mix.
those cheap ass bitches can do anything with ductape.
(PostalDave on ADVrider)
KB's Chief Cats
words hurt, you know
i'm going to go and cut my wrists.
... i don't know who that's more offensive to, either.
yeah i have an old 20 or 30lt off an el-cheapo buninngs which the last guy fucked (10lt of water and he was wondering why it wasn't painting so good) so i took the motor off for a grinder and was going to use for a sandblaster, but haven't, so it might get tacked on...
i'm not a complete dick, despite the prevailing dispersions around here. i've got a regulator on the tank, nail gun reckons it will run from 70-90 IIRC, there is no water in my receiver, nor in the cylinder (it wouldn't stay there long eh, unless it hydraulicly locked up...) and i do use tooling oil, for all my tools.
giz a go on your missus...I like my Paslode guns got 2 of them. 1 for nails and 1 for brads.
On decks I use Paslode Deckfast nails that have groves and a round head. On the gun I use the No-Mar tip that has a rubber block on the end that leave no mark on the decking.
they say that about guns, cyanide and drugs, too...
Hardcore Punk
Got the hammer out yet you lazy fuck?
For a man is a slave to whatever has mastered him.Keep an open mind, just dont let your brains fall out.
KB's Chief Cats
done and dusted boi.Got the hammer out yet you lazy fuck?
*mutter*shitty old galv nails*mutter*mutter*
...still don't have a new compressor though. and as a matter of interest it was 60 nails that went in before the compressor ticked over...
Hardcore Punk
Get a couple of old lawnmower motors and make your own compressor.
For a man is a slave to whatever has mastered him.
Hardcore Punk
Or one like this for the back of ya tractor.
For a man is a slave to whatever has mastered him.
KB's Chief Cats
i have been contemplating a PTO one for the ute...five speedOr one like this for the back of ya tractor.[IMG]
Last edited by Akzle; 5th February 2013 at 20:26. Reason: image deleted, so gremz can't piss and moan.
Hardcore Punk
For a man is a slave to whatever has mastered him.
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote
Bookmarks