I usually go for the 520 chain and sprockets, because I'm a fucken Jew and it's cheaper.
Pm ya shortly about speedo drives.
I usually go for the 520 chain and sprockets, because I'm a fucken Jew and it's cheaper.
Pm ya shortly about speedo drives.
Drew,
The 520 is not standard and the 530 is...
Cant seem to get the 520 in NZ in the configuration I want.
Thanks for sorting the speedo drive.
One for the road...
Kat1230 (81), GSXR1100 (86), RG500 (86)
The 80`s - Back in the days when men looked like women, women dressed like whores and the music F@#KING ROCKED!
I wondered when i seen 630 lol
is this it.
530
520
GS500 250 bandit and many other stuff.
http://www.jtsprockets.com/catalogue/sprocket/JTR823
One for the road...
Kat1230 (81), GSXR1100 (86), RG500 (86)
The 80`s - Back in the days when men looked like women, women dressed like whores and the music F@#KING ROCKED!
Purchased the new sprockets and chain, from just down the road right?
Ask your comer diary for a set of sprockets for an RG500, but with the following spec.
Front - 16 tooth RG500 - 520.....
Rear - 42 from memory... look back to confirm cause that was 247 beers ago, . But a GSX600F 1998 - 520
Advice I have read say not to go under 16 front. To hard on the sprocket and shaft.... Open here for a great comment... "Sprocket and Shaft".. "To Hard!"
But that sort of talk is not accepted in this here forum!
Good luck finding a set..., I found one place -the RGV site in the UK told me where to go, they have a RG500 forum and its good.
http://http://www.bandcexpress.co.uk/
And this shop know its shit... I have emailed them 6 x and they have replied 6 x with pictures.
impressive.
Cost $394 from memory
with chain....
Here are some pictures I am working from:
Notice the hard alloy anodizing... need that! we will talk at length about this.
and finally... I need to get it this straight.
One for the road...
Kat1230 (81), GSXR1100 (86), RG500 (86)
The 80`s - Back in the days when men looked like women, women dressed like whores and the music F@#KING ROCKED!
Just to chew the fat this is an old shed picture.
I need to count how many of these bikes I still have.
One for the road...
Kat1230 (81), GSXR1100 (86), RG500 (86)
The 80`s - Back in the days when men looked like women, women dressed like whores and the music F@#KING ROCKED!
Mate, that's way to much clutter, I'll be happy to wheel a few of those bikes away to clear up some work space for you! Thank me later!
I've always been told, that 14 tooth front sprocket is the smallest size due to it wanting to bind.
The bigger it is of course, the more efficient it becomes...to a point. At some point the weight becomes a limiting factor, and whatever gains you get from the reduced friction are overcome by rotational mass, and the energy required to over come it.
I don't actually know if you can fit a front sprocket big enough for that to become a concern on a motorbike though. Cases start getting in the way over 16 teeth on nearly everything I've worked on...which doesn't include RG500 mind.
Speedo drive on it's way today man. I'll overnight that shit so you can try and fit it tomorrow night with too many beers in ya.
It is not just the back end that's is causing issues, well the front end is too.
Speedo drive is pissing me off, the RG one is no good, outside diameter is too big and the speedo drive forks are too wide. It does not fit.
Got a GSX600 jobby and spacing and everything is perfect, tighten up the axle and its good.
except at the cable input end in to the speedo drive is not the same as the RG... really...really!
yep the Rg and GSX speedo cable drive, end link up are different to the driver.
So I need a custom built cable, RG one end and GSX600 at the other end.
Options appreciated.
And photos to follow ... (tomorrow)
One for the road...
Kat1230 (81), GSXR1100 (86), RG500 (86)
The 80`s - Back in the days when men looked like women, women dressed like whores and the music F@#KING ROCKED!
Note to Drew, thanks for sending me the speedo drive.
It was the same as mine unfortunately but I would not have known if you had not sent it.
The front wheel I removed was not standard so it is good to know.
I sent it back and you should have it this week.
cheers Dude
One for the road...
Kat1230 (81), GSXR1100 (86), RG500 (86)
The 80`s - Back in the days when men looked like women, women dressed like whores and the music F@#KING ROCKED!
Drew,
Your a good man, anyone that willingly to help the cause, is immortal . A nice stance.
Merry Christmas.!
One for the road...
Kat1230 (81), GSXR1100 (86), RG500 (86)
The 80`s - Back in the days when men looked like women, women dressed like whores and the music F@#KING ROCKED!
All I can say is... when you try and light a E Smoke with a lighter its best not to post.
One for the road...
Kat1230 (81), GSXR1100 (86), RG500 (86)
The 80`s - Back in the days when men looked like women, women dressed like whores and the music F@#KING ROCKED!
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks