Yeah I had to buy another set to get into a master cylinder circlip that avoided my other sets.Originally Posted by husaberg
I'd forgotten about this thread.
No8 Wire Extraordinaire
Yeah I had to buy another set to get into a master cylinder circlip that avoided my other sets.
I'd forgotten about this thread.
Don't you look at my accountant.
He's the only one I've got.
Anorak
I was looking for a picture of something and came across one I had posted in the thread.
But every time I go past a second hand shop I always have a rummage through the tools for that amazing tool I never knew I needed.
Odd thing is you hardly ever seem to see real interesting stuff just the same old crap.
where do all the dolly hammers, 3 leg pullers, clamps and spoke shaves go
Kinky is using a feather. Perverted is using the whole chicken
Forum whore
Second hand tool shop in Jackson St, Petone has some diamonds among the dross. Prices tend to be a bit up there.
it's not a bad thing till you throw a KLR into the mix.
those cheap ass bitches can do anything with ductape.
(PostalDave on ADVrider)
No8 Wire Extraordinaire
Never see anything in there worth the iron oxide shite in drawers.
Maybe I should return.
Don't you look at my accountant.
He's the only one I've got.
Bogeyman
A "bit" up there? The prices are an absolute nonsense, the first few times I was in there, (over maybe 5 years) the stock hadn't changed at all, haven't been back in over a decade.
Go soothingly on the grease mud, as there lurks the skid demon
ZZZZZZZZZZ
1 metre long breaker bar. Mint for removing that really tight stuff.
Nunquam Non Paratus
one placenta
...I only ever remember that I should have acquired one of those years before, when there is blood and shit hanging from my knuckles and I've run out of expletives...1 metre long breaker bar. Mint for removing that really tight stuff.
Moped rider
Looks like an expensive bit of 20mm pipe to me...1 metre long breaker bar. Mint for removing that really tight stuff.
No pic, but mine would be a 1.2m long 1/2 drive extension, cos fuck you top bell housing bolts.
ZZZZZZZZZZ
Nah, that's why I have two.
Nunquam Non Paratus
No8 Wire Extraordinaire
Used mine today. So much more control when you have leverage to spare
Don't you look at my accountant.
He's the only one I've got.
Anorak
Just found mine.
On top of the water cylinder?
http://static1.shop033.com/resources...C/15046268.jpg
Kinky is using a feather. Perverted is using the whole chicken
Hardcore Biker
A knob compressor?
Cigar slitter?
"Mummy's Too Tight to Mention" by Simply Red
Anorak
Cable oiler..........
I have had one for about 30 years
https://www.youtube.com/watch?v=crJoG6MsHjQ
Kinky is using a feather. Perverted is using the whole chicken
ZZZZZZZZZZ
Socket I modified with a dremel to torque my Triumph steering head bearings. Worked well, but no longer have a use for it unless I buy another Triumph.
Nunquam Non Paratus
Anorak
Guy I used to work with modified sockets the same as that to undo Honda centrifugal Filter nuts on the singles and clutch centre nuts.Socket I modified with a dremel to torque my Triumph steering head bearings. Worked well, but no longer have a use for it unless I buy another Triumph.
Far cheaper than the proper Honda tool.
Note as a general rule the rear axel can be screwed in used as a puller on most Honda singles flywheels.
Kinky is using a feather. Perverted is using the whole chicken
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote
Bookmarks