Mikuni Smoothbore slides

[Grumph]

Guy in Queensland is sending me a set of four 33mm smoothbore slides to be modified.

They're 1.5 cutaways and he needs 2.0. 1.5's are usually used with open carbs and 2.0 with air cleaners.
He can't find any 2.0 in Oz and I'm quite happy to modify them - but if anyone here wants to do swaps, we're open to that.

Ignore the price.

[husaberg]

Guy in Queensland is sending me a set of four 33mm smoothbore slides to be modified.

They're 1.5 cutaways and he needs 2.0. 1.5's are usually used with open carbs and 2.0 with air cleaners.
He can't find any 2.0 in Oz and I'm quite happy to modify them - but if anyone here wants to do swaps, we're open to that.

Ignore the price.

https://www.jetsrus.com/individual_p...3_198A_su.html THIS IS THE 1.5
Throttle valve 2.0 832-39003-2.0 003-198 2MM
2.5

THIS IS THE STD VM DIMENSIONS
https://www.jetsrus.com/carburetor/c...tle_valve.html

[husaberg]

Seen these today as well
https://www.ebay.com/itm/Mikuni-Smoo...-/143215130989


Plus 35mm i didnt even know they did 35mm
https://www.ebay.com/itm/Kawasaki-KZ...-/173991560820

here is new ones for the 29mm smoothbores
https://www.ebay.com/itm/Mikuni-Bras...4AAOSwgbdcF2E2

and here they are slides for Smoothbore 33's
https://www.ebay.com/itm/Mikuni-Bras...4AAOSwNYtcF2X9

Here is some more
https://www.ebay.co.uk/itm/352672893402

[Grumph]

I'll tell the aussie to look again on ebay. Thanks

[husaberg]

I'll tell the aussie to look again on ebay. Thanks

looking a t the direct site they only have them in 1.5 and 2.5
the other ones were second hand.
WHats so special about the side other than the top bit, what diameter and length are they?
the other thing is what were the std bikes that had them?
could they be available ex factory part off Suzuki Kawasaki etc?

[Grumph]

The 33's were an aftermarket carb only. Most are used open so the 1.5 slides are the most common. The only open carb setup I know of that uses 2.0's is the 1100 Kawasaki. They were never a very popular road carb as most people can't set them up.
In theory you could buy a range of slides but I'd doubt if a lot were actually sold.
They're still a fairly rare carb, most now prefer Keihins as they're much easier to set up properly.

The jets are common Mikuni - but the slides and I think the needles are unique to the 33.

[husaberg]

The 33's were an aftermarket carb only. Most are used open so the 1.5 slides are the most common. The only open carb setup I know of that uses 2.0's is the 1100 Kawasaki. They were never a very popular road carb as most people can't set them up.
In theory you could buy a range of slides but I'd doubt if a lot were actually sold.
They're still a fairly rare carb, most now prefer Keihins as they're much easier to set up properly.

the slide list i seen had the big Suzis and the and big yami's as 2.0 Plus its seems the late Kawaks
I thought the GS1000s and the erl might have had them as std? just looked and they clearly dont........


I would still be keen to know the side measurements