Computer Geeks - Can you help me out? (Broadband & Routers)

[scracha]

604T is pretty much plug in and play with ADSL but it's probably best left to an "expert" to configure it as a bridge. If you can get to the control panel (http://192.168.1.1 (default) or http://10.1.1.1 (Xtra) you could try turning off DHCP & DNS relay and changing the IP range & subnet mask to match your cable modem. There's no uplink port on a 604T so plugging it in to any of the ethernet ports will do the trick. You shouldn't have to arse about with static routing.

[MrMelon]

I would have said start with the basics... find the root cause of your adsl connection problems, unless you just want to go to cable.

Frequent disconnections could be something common like the lines being worked on (but wouldn't affect it over a long period of time), the router, or a fault in the line...

Pass on cable... haven't used that yet...

Cable's so much better than adsl You actually get good speeds both ways and don't have to fight for bandwidth and worry about shitty phone lines! You can also get plans that have unlimited national traffic too through other isp's using the cable network like xnet.

Did you get your router sorted Dave?
If you want the best price on a wireless router, then have a look here http://www.pricespy.co.nz/cat_18.html#g78

[StoneChucker]

Thanks heaps for the replies, I appreciate every drop of knowledge.

Even though I now see that I could have used my current D-Link DSL-G604T ADSL Wireless Router for what I want, I hastily ordered a new router. Never mind though, it's bigger, better, and shinierererer

I got the D-Link DIR-635 RangeBooster N 650. It is designed for the exact uses I want, that being internet gaming, VoIP (Skype internet telephone), security, printer sharing, etc... Although, my current ADSL router shares network printers, the new router is also a 108 Mbps wireless router, not 54Mbps like the old ADSL one. Every little bit helps....

I think I'll be alright with the setup. The TelstraClear technician will install the cable modem. All I have to do is plug the cable modem's ethernet out into the new routers "cable in" ethernet port, and connect my main laptop to one of the ethernet ports on the router's hub (hardwired). Finally use the web-based setup utility for the router, setup my security and add all the MAC addresses of the NIC's of all the computers allowed access, check that all the wireless laptops can access the router. Lastly, add the network printers MAC address, and check all the settings and I should be home and dry. Don't worry, if I need assistance after that I'll definitely take up the kind offers here.

Thanks again guys.
Dave.

PS: I'm not sure if I'm going to sell the ADSL wireless router, if I do though I check in here and let the interested parties know.

[ajturbo]

Hey guys

I have something which I don't quite know how to sort out myself, can you give me the answer or ideas? It's quite detailed, so I'll try keep it as short as I can:

I currently have broadband internet with
ihug (their top "Broadband 4" plan), but am experiencing regular
connection drops and a general reduction in the average
speed I get, which are both new issues. I have decided to
change over to TelstraClears' "LightSpeed 40 (or 80) Residential
High Speed Cable Internet" as that will be up to 4 times
faster than what I get at best on ADSL, and it will be alot
more stable.

I currently connect my main laptop to my wireless ADSL router (D-Link DSL-G604T) using an ethernet cable, and my second laptop connects using
a wireless connection. I also have a third laptop in the house, which
connects wirelessly as well. TelstraClear tell me I can
"piggy-back" / connect the wireless router to their cable
modem once it is installed. This is my preference, as apart
from setting up my current wireless router to connect to the
new cable modem (instead of to ihug via my telephone line),
everything will stay how it is now, making this alot easier. However, I don't think they realised that my current wireless router is an ADSL router - I'm not sure if the two are compatible (Cable to ADSL router to PC?).

I have a web-based setup utility to configure my current
wireless router (D-Link DSL-G604T). I don't know for sure how to change the wireless router's settings to connect to the new cable modem, and get
the connection from there, and not from ihug anymore. The
wireless router has alot of settings, including adsl address
and username and password info, etc, but I won't need that
because the new cable modem will connect to TelstraClear using its settings. So the wireless router only needs to connect and pickup the
connection from the new cable modem, but keep all the other wireless router settings (MAC address of computer network cards authorised to access
the router, as it has security on it), etc... However, this may not even be an issue if I can't use the wireless router.

TelstraClear only provide the one cable modem (no other choices), for a single PC connection. They tell me wireless router setup is easy, but they don't support / help with it.

Can the D-Link DSL-G604T ADSL Wireless Router connect to a CABLE modem and route the traffic as normal? My current wireless ADSL router has a telephone in jack, and 4 ethernet out ports, and obviously the wireless out. I don't see any way to plug in a data cable from the new cable modem.

I think I need to buy a new router, one designed for cable modems. If this is the case, any suggestions? I'm sure it's alot easier than I'm making it out to be. All help / ideas appreciated.

Thanks heaps.
Dave.

throw a BIG brick at it...

[m99dws]

the new router is also a 108 Mbps wireless router, not 54Mbps like the old ADSL one. Every little bit helps.....

Unfortunately this only helps if your card is N, as G cards will still only run at 54mb. I presume you are buying an N card to take advantage of the speed increase? If not it won't make any difference.

[scracha]

I got the D-Link DIR-635 RangeBooster N 650. It is designed for the exact uses I want, that being internet gaming, VoIP (Skype internet telephone), security, printer

I dunno...if you'd said to one of us geeks you were going to buy something..... A TPlink TL-WR642G would have done the job.. 108Mbps and pretty much plug in and play for 100 bucks.

[Wasp]

would you get a better signal strength by using a n accesspoint with a g card versus a g and g?

[m99dws]

G cards will only connect upto 54mb regardless of router speed.

[Wasp]

yes, i know.

answer the question please, or do you mean that it wont change?

[MrMelon]

I doubt the range or signal strength would change since it's in essence just using 2 54Mb signals in parallell in N mode. So using a G card you'd just use one of those signals which would be the same as any other G signal.

Still good stuff Stoney looks pretty flash and more gadgets are always good

[scracha]

Having had a play shifting files accross the network I'd say the signal from the N routers are better which results in less dropped packets and more speed....this is when connected to a "g" PCMCIA card. Could just be the router is more modern tho? MIMO routers are supposedly faster, especially with multiple devices but are still pretty pricey.

All of this is pointless anyway as the wifi speed is still heaps quicker than the broadband speed.

The real fun is finding wifi repeaters that work properly. Phone call to D-Link Aus/NZ last week and after speaking to 3 people they couldn't tell me exactly which cards would work with their own repeater. Hopeless. IEEE or summit should publish some interoperability chart.

I'm surprised some enterprising kiwi isn't manufacturing cheap "home brew" external parabolic antennas.

OMG...I wrote "heaps" so I must be turning Kiwi.

[Gremlin]

"N" routers and everything like that are brand specific, and they are all based off the G protocols, just modified in different ways etc. This means that to gain any performance, you have to buy everything from one brand.

I sooo can't be fucked with wireless etc, and I prefer the ease and speed of gigabit lan. Now I just need a blasted decent internet connection...

[GR81]

If you want the best price on a wireless router, then have a look here http://www.pricespy.co.nz/cat_18.html#g78

wrong! you ask me nicely and get one even cheaper

Unfortunately this only helps if your card is N, as G cards will still only run at 54mb. I presume you are buying an N card to take advantage of the speed increase? If not it won't make any difference.

wrong! 'N' isnt completely ratified yet, you're thinking of 'super-G 108mbps'

"N" routers and everything like that are brand specific, and they are all based off the G protocols, just modified in different ways etc. This means that to gain any performance, you have to buy everything from one brand.

wrong! Super-G is chipset specific... and 90% of them use the 'atheros' chipset
http://www.super-ag.com/superproducts.html <- booyah!

we do SMC here, so if anyone wants cheap wireless gear, let me know and ill sort you out. www.cdlnz.com

[StoneChucker]

Unfortunately this only helps if your card is N, as G cards will still only run at 54mb. I presume you are buying an N card to take advantage of the speed increase? If not it won't make any difference.

You presume correctly, sort of. 95% of the time I connect via ethernet cable, the wireless is for my work laptop and the spare house pc. But yes, I am buying a new wireless network card (SuperG, N, or whatever meets the top specs of 108Mbps).

[Gremlin]

we do SMC here, so if anyone wants cheap wireless gear, let me know and ill sort you out. www.cdlnz.com

BAHAHHAHA, you're joking... we already buy from you guys... nice network cables, along with the other bits and bobs

and just how many south africans do you have working there? One always seems to answer the phone