Tales from the Emporium

[Crim]

They fit the <08 KLR650..

can you flick through the link or is that outfit in HK - USD$18.99 plus USD$5.00 for postage? - looks same same but I would rather go with an outfit that had already been proven
thanks mate, Crim

[NordieBoy]

This is the guy...
http://myworld.ebay.com/i5motorcycle/

They're all selling the same pegs. Usually it's about $18US + postage.

[Woodman]

can you flick through the link or is that outfit in HK - USD$18.99 plus USD$5.00 for postage? - looks same same but I would rather go with an outfit that had already been proven
thanks mate, Crim

Mine has DR footpegs. The DR pin is slightly smaller but works fine and the pegs don't flop around at all. Pretty sure i used DR springs too. You will also need to grind some off so that the pegs will fold up when you fall down.

[Crim]

will fold up when you fall down.

Now that I will NEED to do

[Crim]

Thanks Nordieboy - Footpegs are all on and ready to rock! $NZD30 landed out of Guangzho (Hong Kong?)

[Padmei]

Thanks Nordieboy - Footpegs are all on and ready to rock! $NZD30 landed out of Guangzho (Hong Kong?)

Thats amazing value. Reckon they'll last?

[NordieBoy]

Thats amazing value. Reckon they'll last?

They look beefier than the ones that have been on my DR for the last 4 years.

Not that mine have been crash tested though

Although Shane used them on his TT350 for an enduro at Banks Peninsular and the 3hr cross country on sunday over Tap.



I'm just going to do photos on sunday (eg. get in free).

[gazzerklr]

Is FleaBay hard to find your way around, compared to TM? or is there an easy way?

[NordieBoy]

Is FleaBay hard to find your way around, compared to TM? or is there an easy way?

Biggest problem is finding someone who ships to UnZud.

[marks]

Reckon they'll last?

after extensive testing we have proved that the $18 pegs will bend like a banana if the stony ground of Odlins Rd is applied to them with excessive force

nothing you can ever do will bend them straight again either

[NordieBoy]

after extensive testing we have proved that the $18 pegs will bend like a banana if the stony ground of Odlins Rd is applied to them with excessive force

nothing you can ever do will bend them straight again either

They are cast.

Still, they're less than 1/8th the price of "good" pegs...

[marks]

They are cast.

Still, they're less than 1/8th the price of "good" pegs...

I'd use them again (except I'm a pivot peg convert)

I would just buy two sets instead of one - still cheap

[NordieBoy]

Time I made a dash for the TT350.

There's no idiot lights at all normally.

I want left and right blinkers, battery (key), low beam, high beam.

The LED's are from DSE and are already resistered up for 12v so at 6v they will be a bit dimmer which is a good thing as they're bloody bright on the DR and the high beam one has to be half covered with tape otherwise it kills your night vision.

Bit of model shop plastic left over from when I did the DR a few years ago...


LED's left over from the same time...

[Padmei]

Shouldn't you be shifting dirt instead of having fun?

[NordieBoy]

Shouldn't you be shifting dirt instead of having fun?

Fun?

This isn't fun.

This is serious stuff.





Well, apart from the drill press and hacksaw.
They're always fun.


I also made 2 wooden frames for some more of Jenni's garden beds...