Page 1 of 2 12 LastLast
Results 1 to 15 of 27

Thread: SV and Pirelli help

  1. #1
    Join Date
    19th April 2007 - 20:05
    Bike
    Unicycle
    Location
    Canada (Was NZ)
    Posts
    87

    SV and Pirelli help

    Hey,
    Does anyone run the Pirelli SC1/SC2 Supercorsa's on their Pro Twin bike?

    For the national series in Canada the Pirelli is a spec tire.

    In four races I've spent around NZ$1,500 with the suspension tec's at the track (Yes I know, you guys have it really good getting free advice of Mr Taylor) getting my bike to handle decent with Dunlops for our regional championship and am unfortunately struggling with the Pirelli's.

    In switching I make the adjustments for ride height (circumfrence of tires X pi / 2 then the difference in hieght).

    I heat the Pirelli's to 76C, set the pressures to 32psi F and 28psi R, then head out (as recommended by the Pirelli tec's).

    Pressures coming in are around 33C F and 30.5 R and the temp via the pyrometer is around 41C f and 38C R in the centre of the tire (all good according to the Pirelli tec's)

    Ambient temperature is around 27-31C.

    The problem is a squishy feeling in the front that makes me nervous + ripping through tires. I've kind of combatted this via adding more pressure..... The rear end slides under aggresive power.

    The suspension changes I've made to combat this is:
    reduce oil level in front forks (emulated dampener rods at present) and increase pre load 2mm to raise the working part of the suspension out of the poor progression area.

    With the rear I've reduced the compression and increased the pre-load (to soften and lift out of poor progression area).

    All I'm wanting to know is:
    Is there anyone who has had racing success with the super corsa's on a SV?
    If so, what are the tire pressures and temp going out/in?
    Do you know how you set up compares to the setting for Dunlop 209's?
    What way do you adjust the pressure's for changes in temperature?
    Anything else you've noted?

    Cheers and thanks for your help in advance!!
    Last edited by JJ58; 13th June 2008 at 02:16. Reason: spelling mistake

  2. #2
    Join Date
    17th November 2002 - 11:00
    Bike
    XB12R, FXR150, Ducati 400ss, 1125CR
    Location
    dam.. i move too much
    Posts
    5,047
    think you best save ya money and go bucket racing...


    what a ride so far!!!!

  3. #3
    Join Date
    29th July 2006 - 09:19
    Bike
    WR269f, WR450f
    Location
    Napier
    Posts
    2,585
    Quote Originally Posted by JJ58 View Post
    Hey,


    I heat the Pirelli's to 76C, set the pressures to 32psi F and 28psi R, then head out (as recommended by the Pirelli tec's).
    Pressures coming in are around 33C F and 30.5 R and the temp via the pyrometer is around 41C f and 38C R in the centre of the tire (all good according to the Pirelli tec's)
    Shouldn't your pressure should be set on a cold tyre not a heated one,thats why your not getting much of a change in pressure when ya come back in,my understanding is there should be around a 4-6 psi increase.
    Which in turn will let your tyres shear from being underinflated.
    I inadvertedly ran 26psi cold in my front for a day and it started to tear,then next day ran 31 cold and it revived the tyre really well.
    Different bike I know but same tyres

  4. #4
    Join Date
    13th December 2004 - 10:05
    Bike
    SV400
    Location
    New Zealand
    Posts
    2,173
    Somethings definately not right if your chewing out fronts. SC0 fronts seem to last for ages normally. Our current F3 national champ (codgyoldracer) runs Pirelli's on his SV650 but I think its widely accepted that Dunlop N-Tecs are the go at the moment.

    I had this problem once and went through 2 front tyres at one meeting. This was with a GSXR front end in the SV. I first thought I was causing it by trailing the front brake deep into the corner but latter found it was one of the dampening rods was coming apart.

    I would lift the front of the bike remove the front wheel and fork springs and emulators then move the forks by hand to see if they are both the same without any sticking etc. Then set the emulators and make sure they are in the right way (relieve spring to the top). Check the oil levels by sliding the fork legs all the way up without springs in and measuring.

    Not to sure were should be going with front tyre pressure but 30psi cold is a good starting point.

    Sorry if the above sounds a bit simplistic but its just what I would try as well as going back to baseline settings on the rear shock.

  5. #5
    Join Date
    19th April 2007 - 20:05
    Bike
    Unicycle
    Location
    Canada (Was NZ)
    Posts
    87
    Cheers GSVR, always good to check the obvious.

    forks are in tack, emulators seated correctly and correct oil level (measured with springs in).

    Pirelli International always recommends setting tyre pressures warm @ 76C.... Only Dunlops are to be set cold.

    Suspension is in functional working order. The info I'm after is really any info on spring rate/valving changes between using each tire....Also nitrogen is used as recommended by Pirelli, therefore fading not really an issue.

    Cheers
    Last edited by JJ58; 13th June 2008 at 12:27. Reason: Spelling mistake.

  6. #6
    Join Date
    13th January 2004 - 11:00
    Bike
    Honda PC800
    Location
    Henderson -auckland
    Posts
    14,163
    I Ran the SC0 on the front of my SV for 2 full seasons with no issues with the front tyre. I would strongly suggest you might want to do your tyre pressures cold and at 32psi as a starting point.
    I did find they "announced" when they were close to their limits pretty well.
    To see a life newly created.To watch it grow and prosper. Isn't that the greatest gift a human being can be given?

  7. #7
    Join Date
    11th June 2007 - 08:55
    Bike
    None
    Location
    New Plymouth
    Posts
    5,053
    Quote Originally Posted by JJ58 View Post
    Hey,
    Does anyone run the Pirelli SC1/SC2 Supercorsa's on their Pro Twin bike?

    For the national series in Canada the Pirelli is a spec tire.

    In four races I've spent around NZ$1,500 with the suspension tec's at the track (Yes I know, you guys have it really good getting free advice of Mr Taylor) getting my bike to handle decent with Dunlops for our regional championship and am unfortunately struggling with the Pirelli's.

    In switching I make the adjustments for ride height (circumfrence of tires X pi / 2 then the difference in hieght).

    I heat the Pirelli's to 76C, set the pressures to 32psi F and 28psi R, then head out (as recommended by the Pirelli tec's).

    Pressures coming in are around 33C F and 30.5 R and the temp via the pyrometer is around 41C f and 38C R in the centre of the tire (all good according to the Pirelli tec's)

    Ambient temperature is around 27-31C.

    The problem is a squishy feeling in the front that makes me nervous + ripping through tires. I've kind of combatted this via adding more pressure..... The rear end slides under aggresive power.

    The suspension changes I've made to combat this is:
    reduce oil level in front forks (emulated dampener rods at present) and increase pre load 2mm to raise the working part of the suspension out of the poor progression area.

    With the rear I've reduced the compression and increased the pre-load (to soften and lift out of poor progression area).

    All I'm wanting to know is:
    Is there anyone who has had racing success with the super corsa's on a SV?
    If so, what are the tire pressures and temp going out/in?
    Do you know how you set up compares to the setting for Dunlop 209's?
    What way do you adjust the pressure's for changes in temperature?
    Anything else you've noted?

    Cheers and thanks for your help in advance!!
    Questions and suggestions relevant to your problems;

    1) Are the damper rods original and modified or are they Traxxion rods? ( These are very good and I have just ordered some more off Traxxion for the NZ market ) If they are oem and have been modified in the Race Tech suggested method you actually get a dead area of high speed rebound damping.
    2) Are the 64 lb/in poppet springs fitted and how many turns of preload?
    3) Oil level with emulators in and springs removed, forks in full closed position?
    4) Oil viscosity ( preferably centistroke rating at 40 degrees celsius ) and brand?
    5) Spring rate and static sag?
    6) Your weight and height?
    7) What spring rate is fitted into the Penske rear shock?
    8) What length are you running the shock at?
    9) Is it the standard piston in that shock, a Penske digressive or a Traxxion progressive? Or is it a piston that provides a steep slope to the damping curve to ''catch'' long stroke movements? If the rear end is sliding too readily ( and the spring rate is okay ) then the internal valving and bleed bypass is too aggressive and no amount of external clicker fiddling will correct it. I am not there on the spot but I am guessing that the front and rear are perhaps also not balanced in action, the rear is underworking and thereby overworking the front................but I may be wrong.
    The carcass construction between Pirelli and Dunlop is different and it will load the suspension differently. I am sure that following your answers we can provide some plausible suggestions.

    Ph: 06 751 2100 * Email: robert@kss.net.nz
    Mob: 021 825 514 * Fax: 06 751 4551

  8. #8
    Join Date
    19th April 2007 - 20:05
    Bike
    Unicycle
    Location
    Canada (Was NZ)
    Posts
    87
    Wow Tony, 32psi cold is high and miles away from the manufacturers recommendation. I might try it, but I bet you struggle for grip in the rear on corner exit. I tried 32psi warm in the rear and it was like I was dirt tracking. The top super bike guys run about 26psi warm on these rear tires to get the grip coming out of the corner. Pirelli advise to not take the rear above 31psi warm.

    The bike did chew tires up for a bit, but I fixed that by making the suspension changes above, as the SV's have a poor progression linkage/dampning.

    The issue with tire wear is that the Pirelli's are far softer than the Dunlop's so naturally I'll be wearing them out sooner. The Dunlop's are triple compound and have a stiffer carcase. Hence the 30 laps to a tire compared to the 200+ laps on the Dunlops at speed.

    So it looks like no-one has had a good tire testing session to work out the differences? I'm getting pretty close and it's costing a lot (thank goodness we get prize money here). I'll post up what I find out.

    Cheers

  9. #9
    Join Date
    19th April 2007 - 20:05
    Bike
    Unicycle
    Location
    Canada (Was NZ)
    Posts
    87
    Cheers Robert.
    I'm away from my notes at the mment, but will get back to you in the next few days with the info.

    Just for clarification the "not balanced in action" means that mid corner there is not correct weight allocation the the front and back of the bike?

  10. #10
    Join Date
    19th April 2007 - 20:05
    Bike
    Unicycle
    Location
    Canada (Was NZ)
    Posts
    87
    Hey Frosty....Just for your info:
    http://www.orionmotorsports.ca/prod_nitrogen.htm

    Check out the tire pressures.

  11. #11
    Join Date
    13th January 2004 - 11:00
    Bike
    Honda PC800
    Location
    Henderson -auckland
    Posts
    14,163
    Quote Originally Posted by JJ58 View Post
    Hey Frosty....Just for your info:
    http://www.orionmotorsports.ca/prod_nitrogen.htm

    Check out the tire pressures.
    I think that may be the difference--we just run air mostly
    To see a life newly created.To watch it grow and prosper. Isn't that the greatest gift a human being can be given?

  12. #12
    Join Date
    4th January 2005 - 18:50
    Bike
    Massey ferguson 7495 dyna-vt
    Location
    Norfland
    Posts
    6,917
    Quote Originally Posted by Tony.OK View Post
    Shouldn't your pressure should be set on a cold tyre not a heated one,thats why your not getting much of a change in pressure when ya come back in,my understanding is there should be around a 4-6 psi increase.
    Which in turn will let your tyres shear from being underinflated.
    I inadvertedly ran 26psi cold in my front for a day and it started to tear,then next day ran 31 cold and it revived the tyre really well.
    Different bike I know but same tyres
    pressure is best set hot...at track running temp...
    Quote Originally Posted by Drew View Post
    Given the short comings of my riding style, it doesn't matter what I'm riding till I've got my shit in one sock.

  13. #13
    Join Date
    11th June 2007 - 08:55
    Bike
    None
    Location
    New Plymouth
    Posts
    5,053
    Quote Originally Posted by JJ58 View Post
    Cheers Robert.
    I'm away from my notes at the mment, but will get back to you in the next few days with the info.

    Just for clarification the "not balanced in action" means that mid corner there is not correct weight allocation the the front and back of the bike?
    That is a good part of it yes, its also about controlled weight transfer.
    And yes as per your previous post the rear linkage on that bike is more than a little wanting, it was built as a commuter bike and not as a race bike.
    This is one of the models we always have a little difficulty setting up, although I havent mapped it I suspect that the motion ratio that the linkage imparts to the shock is very lazy i.e it only moves the shaft slowly, at least in the first part of travel. That means the damping build up is slow and a relatively aggressive damping spec ( internally ) has to be arranged. The problem being is that if you are so reliant on damping to hold it in its stroke the setting window becomes much narrower between what works and what doesnt. In all fairness that basic problem is irrespective of what shock is fitted into the rear, although some shock designs are more fundamentally accomodating of the issue. I also suspect that raising ride height ( by shock length ) may in fact swing the linkage into a dead zone of movement.
    Before anyone else may suggest it why not just fit firmer springing? The answer is that yes it will ''fudge it'' a bit BUT the spring force will ramp up much more at longer stroke movements giving a very harsh ride. And it will step out too readily finishing the turns under power. Its always a fine balance between springing and damping. Oversimplistically ( and I keep repeating this everywhere ) springing is about position and damping is about rate of change of position.
    Heck I may get some data off Ohlins re this as it has for too long been a niggling question in the back of my mind.
    And another question, does the bike have any inkling of a tendency to ''stand up'' mid corner?

    Ph: 06 751 2100 * Email: robert@kss.net.nz
    Mob: 021 825 514 * Fax: 06 751 4551

  14. #14
    Join Date
    4th January 2005 - 18:50
    Bike
    Massey ferguson 7495 dyna-vt
    Location
    Norfland
    Posts
    6,917
    Quote Originally Posted by FROSTY View Post
    I think that may be the difference--we just run air mostly
    I think you have been more likely misinformed frosty...
    Quote Originally Posted by Drew View Post
    Given the short comings of my riding style, it doesn't matter what I'm riding till I've got my shit in one sock.

  15. #15
    Join Date
    4th January 2005 - 18:50
    Bike
    Massey ferguson 7495 dyna-vt
    Location
    Norfland
    Posts
    6,917
    Quote Originally Posted by Robert Taylor View Post
    .
    Before anyone else may suggest it why not just fit firmer springing? The answer is that yes it will ''fudge it'' a bit BUT the spring force will ramp up much more at longer stroke movements giving a very harsh ride.
    Okay I was thinking that just the second yo wrote that last piece...hmmm...what about running a higher spring rate with shortening the lenght [eye to eye] of the shock..and running slightly less sag? or would that still be in the sense of 'FUDGING IT' ???
    Quote Originally Posted by Drew View Post
    Given the short comings of my riding style, it doesn't matter what I'm riding till I've got my shit in one sock.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •