Results 1 to 9 of 9

Thread: Big annoucment for Big Dan

  1. #1
    Join Date
    9th December 2006 - 18:32
    Bike
    dont have one "YET"
    Location
    auckland
    Posts
    123

    Big annoucment for Big Dan

    As i've recently become engaged and have decided to make the move out of the big smoke and move to where my Fiancee lives in Hamilton

    I'm Planning on moving down in jan/Feb depending on the job front which leads me to my reason for this thread

    I would like to know if any of you out there in KB land got any full time jobs going that starts in jan/feb

    I'm not the office bum type and i'm looking at $15-17 per hour pay rate and i'd like a guaranteed 40-45 hours preferably day shift or evening shift NO night shifts

    I have my Forklift Lic and F Endorsment and Full Car Lic and own car


    Any help would be greatly appricated

    Cheers
    Dan

  2. #2
    Join Date
    22nd January 2006 - 14:26
    Bike
    Er6n
    Location
    Wellington
    Posts
    1,001
    Congrats Dude!!!!!!
    Reckless says "I like the crusty bits on the outside"

  3. #3
    Join Date
    1st August 2007 - 21:17
    Bike
    None at the moment
    Location
    Cromwell
    Posts
    1,788
    Good on ya mate....Hope you have better luck on the Job front than I am at the moment (Hamilton is bigger than Otaki, so you will be fine)....


  4. #4
    Join Date
    5th February 2008 - 13:07
    Bike
    2006 Hyosung GT650R
    Location
    BOP
    Posts
    7,141
    Congrats Dan you big softie. If you DID want to move down there right NOW, I can probably line some work up for you for the summer, but it will probably quieten off a bit once you are into the winter - plenty of time to carry you over in the meanwhile and find a proper job. PM me if you are keen and I'll make some calls.

    Steve
    "I am a licenced motorcycle instructor, I agree with dangerousbastard, no point in repeating what he said."
    "read what Steve says. He's right."
    "What Steve said pretty much summed it up."
    "I did axactly as you said and it worked...!!"
    "Wow, Great advise there DB."
    WTB: Hyosung bikes or going or not.

  5. #5
    Join Date
    24th November 2005 - 12:40
    Bike
    anything I can get my grubby wee paws on
    Location
    Outside
    Posts
    1,532
    Quote Originally Posted by Big Dan View Post
    As i've recently become engaged
    Dont want to rain on your parade

    But as one of the married prisoners on this forum

    I have to say I think you are making a mistake

    Dont do it

    Its not too late

    (yet)
    =mjc=
    .

  6. #6
    Join Date
    29th March 2006 - 18:06
    Bike
    XJR 1300
    Location
    Hawkes Bay
    Posts
    1,085
    Quote Originally Posted by jim.cox View Post
    Dont want to rain on your parade

    But as one of the married prisoners on this forum

    I have to say I think you are making a mistake

    Dont do it

    Its not too late

    (yet)


    haha..dude aren't no prison that allows you's too leave without clocking out....
    .xjr....."What's with all the lights"..officer..

  7. #7
    Join Date
    5th June 2008 - 09:07
    Bike
    :-( none at present
    Location
    Turangi
    Posts
    1,115
    Well done mate. You doing down to be with her is a big step. It will work out for you.
    If you are behind meDont ask as I am lost too.

  8. #8
    Join Date
    13th May 2003 - 12:00
    Bike
    Thinking
    Location
    Around
    Posts
    7,383
    there is SHITLOADS of forklift work here mate Fonterra is a biggy with the new big storehouse, I wouldnt even worry until you got here you wont have a prob getting a job
    Ive run out of fucks to give

  9. #9
    Join Date
    17th February 2007 - 23:51
    Bike
    ET-05 ZX6RR,08 ZX10-R A Green One
    Location
    Glenbrook
    Posts
    347
    Congrats dude...
    Marriage is a fine institution....everyone should be committed..
    Quote Originally Posted by peasea View Post
    It could be argued that to put anyone on a ZX10 is "just stupid".



    CNC Machining,Precision Engineering,Thermal Coatings/Metalization,
    Msg me....

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •