Page 2163 of 2625 FirstFirst ... 1163166320632113215321612162216321642165217322132263 ... LastLast
Results 32,431 to 32,445 of 39365

Thread: ESE's works engine tuner

  1. #32431
    Join Date
    18th March 2012 - 08:35
    Bike
    Homebuilt chassi, Kawasaki 212cc
    Location
    Sweden
    Posts
    660
    Successfully relocated pins:


  2. #32432
    Join Date
    20th January 2010 - 14:41
    Bike
    husaberg
    Location
    The Wild Wild West
    Posts
    11,823
    Quote Originally Posted by Katman View Post
    I reminder distinctly .




    Kinky is using a feather. Perverted is using the whole chicken

  3. #32433
    Join Date
    1st May 2016 - 13:54
    Bike
    Vintage 2T
    Location
    Brisbane
    Posts
    431
    .
    .
    EFFEN Football!!??

    Is this the ESEsWET Jumping the Shark Moment?



    Cheerless Daryl.

  4. #32434
    Join Date
    21st March 2014 - 22:00
    Bike
    RZ350, TZR250 3XV, TZR250 3MA, TZR125
    Location
    Hanau, Germany
    Posts
    137

    YZR500 replica..

    May be some of you have seen that, I like it...

    http://forum.2temps.fr/viewtopic.php?f=8&t=19432

  5. #32435
    Join Date
    18th March 2012 - 08:35
    Bike
    Homebuilt chassi, Kawasaki 212cc
    Location
    Sweden
    Posts
    660
    When designing a crankshaft, Lesson number one: Do NOT exaggerate the interferencefit, sometime somebody maybe want to rebuild it.
    Quite disappointed now as the bolt wouldn´t move when pressing with a shitload of force(over 40tonnes).
    And the material around the lighteningpockets on the inside collapsed instead.

    Click image for larger version. 

Name:	vevparti.jpg 
Views:	371 
Size:	115.0 KB 
ID:	342752

    Sad day.

  6. #32436
    Join Date
    25th March 2004 - 17:22
    Bike
    RZ496/Street 765RS/GasGas/ etc etc
    Location
    Wellington. . ok the hutt
    Posts
    20,500
    Blog Entries
    2
    Oh. That's upsetting
    Don't you look at my accountant.
    He's the only one I've got.

  7. #32437
    Join Date
    18th May 2007 - 20:23
    Bike
    RG50 and 76 Suzuki GP125 Buckets
    Location
    Auckland
    Posts
    10,473
    .
    If the big end and rod are completely ruined the trick is to hold the rod in a vice. And cut through the rod and big end pin with a disk grinder. Then you have the two flywheel halves to deal with separately. Much easier to place one crank half in the press to press the remains of the pin out.

  8. #32438
    Join Date
    28th November 2013 - 21:58
    Bike
    Dawes Jaguar
    Location
    UK
    Posts
    435
    Presumably it took a lot, or excessive, amount of force to assemble it in the first place, and was difficult to align?

  9. #32439
    Join Date
    18th March 2012 - 08:35
    Bike
    Homebuilt chassi, Kawasaki 212cc
    Location
    Sweden
    Posts
    660
    It was almost impossible to align the crank i noticed earlier, it took very high forces to get it to move just a couple of thousands of a millimeter.

  10. #32440
    Join Date
    24th July 2006 - 11:53
    Bike
    KTM 890 Adventure
    Location
    Wgtn
    Posts
    5,541
    Quote Originally Posted by TZ350 View Post
    .
    If the big end and rod are completely ruined the trick is to hold the rod in a vice. And cut through the rod and big end pin with a disk grinder. Then you have the two flywheel halves to deal with separately. Much easier to place one crank half in the press to press the remains of the pin out.
    I once had a similar problem, compounded by a lack of intelligence in failing to support crank halves immediately surrounding the pin and over enthusiastic use of a very large press. Better tooling might have worked, but experience with similar assemblies suggested another approach. Pushing the end of a shaft swells that end and increases the radial pressure against its bore, I've felt this many times where it takes more force to remove a shaft than it took to initially install it, in some cases the increase in force is indeed enough to distort the shaft beyond it's elastic limit, at which point you're buggered.

    One solution is to make the pin hollow, (which is common enough) but not for its full length. Pressing against the bottom of this pin hole is effectively the same as pulling it out, which slightly stretches it, microscopically reducing the diameter, the opposite effect of applying force to the upper face. The force required to disassemble the shaft where I first used that design is about 60% of the original with the same fit.
    Go soothingly on the grease mud, as there lurks the skid demon

  11. #32441
    Join Date
    20th January 2010 - 14:41
    Bike
    husaberg
    Location
    The Wild Wild West
    Posts
    11,823
    The mother country had this stuff sorted years ago
    Click image for larger version. 

Name:	6.jpg 
Views:	153 
Size:	45.3 KB 
ID:	342753Click image for larger version. 

Name:	VilliersCrank.jpg 
Views:	171 
Size:	74.5 KB 
ID:	342754Click image for larger version. 

Name:	Manx-Norton-Crank-Assy-500-Long-Stroke-International.jpg 
Views:	152 
Size:	42.6 KB 
ID:	342755
    Quote Originally Posted by Katman View Post
    I reminder distinctly .




    Kinky is using a feather. Perverted is using the whole chicken

  12. #32442
    Join Date
    18th May 2007 - 20:23
    Bike
    RG50 and 76 Suzuki GP125 Buckets
    Location
    Auckland
    Posts
    10,473
    Click image for larger version. 

Name:	YAMAHA-KT100S-CRANKSHAFT.jpg 
Views:	158 
Size:	37.9 KB 
ID:	342758

    The Yamaha KT100 kart engine used steel plugs inserted in the end of the big end pin to expand it and lock it in place.

    To disassembly it, before pressing, you drilled one plug out and then tapped the other side out with a pin punch.

    Quote Originally Posted by Ocean1 View Post
    Pushing the end of a shaft swells that end and increases the radial pressure against its bore, I've felt this many times where it takes more force to remove a shaft than it took to initially install it, in some cases the increase in force is indeed enough to distort the shaft beyond it's elastic limit, at which point you're buggered.

    One solution is to make the pin hollow, (which is common enough) but not for its full length. Pressing against the bottom of this pin hole is effectively the same as pulling it out, which slightly stretches it, microscopically reducing the diameter, the opposite effect of applying force to the upper face. The force required to disassemble the shaft where I first used that design is about 60% of the original with the same fit.
    I like Ocean1's approch very much.

  13. #32443
    Join Date
    13th December 2018 - 18:06
    Bike
    youtube andreas länström
    Location
    sweden
    Posts
    286
    Why not disassemble it from the other dirction, one half at the time?

  14. #32444
    Join Date
    19th October 2014 - 17:49
    Bike
    whatever I can get running - dirt/track/
    Location
    San Francisco
    Posts
    382
    Quote Originally Posted by jamathi View Post
    The problem of breaking shafts was solved by fitting a shock absorber.
    Something like old English bikes had....
    It appears that the twin cylinder Seadoo model 580 2T that takes the rotary valve drive from between the cylinders has a spring on the drive shaft that may let the skew gear float a bit which might serve as a damping device.

    cheers,
    Michael
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	SeaDoo580RotaryValveDriveShaft.jpg 
Views:	94 
Size:	41.8 KB 
ID:	342762  

  15. #32445
    Join Date
    4th September 2017 - 10:39
    Bike
    Daelim besbi 2008
    Location
    España
    Posts
    300
    Quote Originally Posted by Flettner View Post
    If the sleeve thing doesn't work, we will just lower the exhaust ports and re cast as an FOS cylinder.

    Sorry, I'm curious, your new project is related to this statement.

Thread Information

Users Browsing this Thread

There are currently 57 users browsing this thread. (1 members and 56 guests)

  1. jamathi

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •