Bucket bits wanted & services needed

[husaberg]

think i have sorted it , only had 5 volts running to it which think was for the tps , put 12 volts on it and ran fast

Great if worse comes to worst you could just hook them up to the oil pump cable (KISS)
I got crucified for saying that once............

[mr bucketracer]

Great if worse comes to worst you could just hook them up to the oil pump cable (KISS)
I got crucified for saying that once............

was thinking that (-; ,its going now but in reverse so need a cable for computer to fix

[husaberg]

was thinking that (-; ,its going now but in reverse so need a cable for computer to fix

Its an DC motor isn't it, just reverse the wires or mount it in the opposite direction.

[mr bucketracer]

Its an DC motor isn't it, just reverse the wires or mount it in the opposite direction.

it worked bye passing the ecu but hooked up it was a no go

[husaberg]

it worked bye passing the ecu but hooked up it was a no go

What PGM are you running? Also is the gear indicator and TPS hooked up?
there is a gUy that specialise in repairs to Honda PGMs that occasionally posts on ESE.
Its this Guy http://www.2t-racelab.com/
I can't remember what his username is BUT IT SOMETHING GREEK.

[mr bucketracer]

It's a inknetech .bloody thing will not pick up a signel

[husaberg]

It's a inknetech .bloody thing will not pick up a signel

There is a thread for that as well but just ask Mike.(Speedpro)

Paging Mike.

http://www.kiwibiker.co.nz/forums/sh...light=ignitech

[mr bucketracer]

It's the usb port needs some shit down loaded. All ready wasted hours on this

[mr bucketracer]

how do i down load a usb program and put on a usb chip to put on another computer ..........found a disk !!!!!!! and failed

[Drew]

Its an DC motor isn't it, just reverse the wires or mount it in the opposite direction.

Erm, have you ever tested that? An electric motor won't spin the other way by simply reversing the feed. AC or DC.

[Bert]

how do i down load a usb program and put on a usb chip to put on another computer ..........found a disk !!!!!!! and failed

Erm, have you ever tested that? An electric motor won't spin the other way by simply reversing the feed. AC or DC.

Problem solved and all working nicely.

Something that we have found with all the NSRs is each one is a little different in terms of voltage output. Modified the map and away you go.

Really impressed by Scott pipes, seems like they will produce some great midrange punch. Some back to backs to be done with the TYGA options and see what comes out of it.

[wildman]

Erm, have you ever tested that? An electric motor won't spin the other way by simply reversing the feed. AC or DC.

Works fine on DC that's how most electric window motors work, funny when someone complains their aftermarket electric fan goes the wrong way. Black isn't always negative

[husaberg]

Erm, have you ever tested that? An electric motor won't spin the other way by simply reversing the feed. AC or DC.

It depends on the set up, if it is a permanent magnet motor you can easily as I stated just reverse the polatity.
if its an electronically controlled one with a built in circuit board you can't do it that way , I sincerely doubt the 1990's NSR servo is though.

I also note its really easy to reverse a AC motor esp a three phase one.
A single phase just requires the reversing of the start windings (just swapping a couple of wires I did one the other day it took about 2 minutes)
the instruction on how to do so are normally under the starter Cap box.

[Henk]

Has anyone got a pipe or an FXR kicking around surplus to requirements? I'm thinking of putting together an interim club hack out of spare parts and that's about the one pence I'm missing.

[TALLIS]

I have a good exhaust can down to the original mount by the foot peg, no front pipe that I can find. If that will do, yell out and ill bring it up to tamas.