Bucket bits wanted & services needed

**F5 Dave** · 5th January 2018, 17:02

Square barrel type. Pretty things pickings in NZ. We only got a few grey imports.

**Bert** · 7th January 2018, 19:32

Originally Posted by F5 Dave

Square barrel type. Pretty things pickings in NZ. We only got a few grey imports.

Where they full cast Iron or alloy & iron sleeve?

If they where full cast iron, then you could look at the DT50mx (1981-1996), Post 96 they seem to be AM6.

**flyonly** · 7th January 2018, 20:21

Originally Posted by Bert

Where they full cast Iron or alloy & iron sleeve?

If they where full cast iron, then you could look at the DT50mx (1981-1996), Post 96 they seem to be AM6.

Your right. The DT50LC are the same. It’s a cast iron cylinder.

Sent from my iPhone using Tapatalk

**ATAl** · 1st March 2018, 10:16

Does anyone pulling apart a FXR150 have a working speedo sender they want to sell/swap? Just found that the insides of my one have gone missing.

I can swap a non-working sender if you need it as a wheel spacer.

**Delphinus** · 9th March 2018, 14:02

Anyone got their original FXR150 carb they pulled off? Needing to replace mine, and don't need anything special since bike is just used for commuting around town. Ideally Dunedin/Otago based?

**timg** · 9th March 2018, 19:38

Originally Posted by Delphinus

Anyone got their original FXR150 carb they pulled off? Needing to replace mine, and don't need anything special since bike is just used for commuting around town. Ideally Dunedin/Otago based?

Yep. Know anybody heading down from Chch that can pick it up for you from Rolleston?

**Delphinus** · 10th March 2018, 09:21

Originally Posted by timg

Yep. Know anybody heading down from Chch that can pick it up for you from Rolleston?

Not off the top of my head. Happy to pay freight. Sent you a PM.

**husaberg** · 4th April 2018, 20:33

Still looking for a set of TZR250 1KT forks if anyone has some or some early FZR1000 forks. rusty or bent okay ...

**Stubbs321** · 21st May 2018, 18:27

I am looking for a tuned expansion chamber for a RX125, can anyone point me in the direction of someone with one.

Or

Any information on anyone building expansion chambers would be appreciated.

**TZ350** · 24th May 2018, 21:07

I have had good results with a Honda NF4 RS125 chamber.

**Drew** · 25th May 2018, 13:41

Originally Posted by husaberg

Still looking for a set of TZR250 1KT forks if anyone has some or some early FZR1000 forks. rusty or bent okay ...

There's a chance I have some. Got FZR something forks, any identifying features?

**husaberg** · 25th May 2018, 18:30

Originally Posted by Drew

There's a chance I have some. Got FZR something forks, any identifying features?

39mm forks on the tzr2501kt single disk.
41mm on the FZR1000
They both have 100mm centers on the calipers and tall spacing for 320mm disks
Not totally sure but i think both are 15mm front axel.
They have the mudguard mounts on top by the seals rather than on the side.

**jonny quest** · 26th May 2018, 09:10

Possibly looking for a rolling chassis, VJ22 or RS250 streetbike. I am in USA. Will pay for freight if that's an option.

**F5 Dave** · 26th May 2018, 09:53

Have you tried Japan broker sites to buy outside of Japan?
That sort of stuff has shot up in value insanely here in last 10 years.

**Drew** · 26th May 2018, 12:54

Originally Posted by husaberg

39mm forks on the tzr2501kt single disk.
41mm on the FZR1000
They both have 100mm centers on the calipers and tall spacing for 320mm disks
Not totally sure but i think both are 15mm front axel.
They have the mudguard mounts on top by the ]

Ones I have don't have the mudguard mounts like that.