Bucket bits wanted & services needed

[diablo]

Not sure if the swing arm is the same. But I have been working on an XR100. I managed to get a FZR 17 inch to fit into the rear with a 115 x 17 Slick. As for the front end I had a nicely setup CB125 twin forks and FZR front wheel. The forks fitted straight into the original tripple clamps. The only issue might be with the stock rear shocks .. Should be a good F5 tho (when I get round to finishing it !!)
Steve

May be the same, depending on how old yours is..
I'm waiting to hear back re tyres (not slicks).
If I can't get anything decent, I think I may lace up some 17" rims to some hubs I have.. then get the slicks.
Or get some different forks (31mm - I have a list of all the bikes with this size forks)..
Rear shocks - I am putting my old XV250 (Virago) shocks on mine - 40mm lower..

[Gazzza]

Does anyone have an old frame kicking around going cheap... All I need is the steering head (with bearings)and top and bottom yokes... Any sort of frame as long as it's not alloy. Need it for a sidecar. Cheers.

[Gigglebutton]

Does anyone have an old frame kicking around going cheap... All I need is the steering head (with bearings)and top and bottom yokes... Any sort of frame as long as it's not alloy. Need it for a sidecar. Cheers.

I have a GP125 frame. If thats any good to you, I'll cut the head out

[Ivan]

anyone have any xl or xr 125 or 185 or 200 heads cam and ignitors as im converting my old 1 piece xl125 motor to 2 piece head and going to run total loss cdi setup

[Pumba]

Does anyone have an old frame kicking around going cheap... All I need is the steering head (with bearings)and top and bottom yokes... Any sort of frame as long as it's not alloy. Need it for a sidecar. Cheers.

Got a steering head off a GJ72A GSXR250 (yes just a steering head, rest of the frame has gone to scrap) and a set of FXR triple clamps that fit it, should have some old bearings to go with it as well. It yours if you want it.

[Gigglebutton]

Looking for an exhaust system, mainly the expansion chamber something that would allow this little motor to peek the rpm’s much faster and more responsive than it is going at now!!!

Thanks ya’al

I have got the pipe at work & Henk will pick up when he picks up his CB head. It was no good on my RG, but it may match your porting better. Good luck with it

[Gazzza]

I have a GP125 frame. If thats any good to you, I'll cut the head out

Hi mate, I might grab the steering head off Pumba save you cutting up your frame thanks for the offer though.

[Moooools]

Anybody have an rg50 motor that they want to sell. Or any other water cooled 50cc 2-stroke for that matter.

Let me know.

[Yow Ling]

Anybody have an rg50 motor that they want to sell. Or any other water cooled 50cc 2-stroke that matter.

Let me know.

I have a RZ50 motor, needs a rod kit and no ignition, PM me if you are interested

[Moooools]

Anybody want to pick up an RS 125 frame for me in Christchurch, pack it up and ship it to me?
Or if anybody is heading up this way soon?
I might even let you touch it.

Cheers
Max

[F5 Dave]

I have an RG50 engine with RS125 mounts for it about to go begging (not my no27 or anything of course).

[koba]

There eyes met from across the room, the both realised immediatly it was a perfect match...

[chrisc]

Anyone out there have a '82 CG125 guage cluster? The square one in KPH.
Cheers

[Gigglebutton]

I have an RG50 engine with RS125 mounts for it about to go begging (not my no27 or anything of course).

Im keen. I want to put an rg in the RS i have for my daughter. so we can race in f5 together

[Gigglebutton]

Anybody want to pick up an RS 125 frame for me in Christchurch, pack it up and ship it to me?
Or if anybody is heading up this way soon?
I might even let you touch it.

Cheers
Max

So you won it. Grrrrrr I hoped i lost to another bucket racer