Bucket bits wanted & services needed

**koba** · 14th December 2011, 14:40

Originally Posted by Muzzab

Probably a long shot, but does any one out there have an exhaust or even just a header pipe for a FXR surplus to requirements.
Failing that, any suggestions on any other suitable donor pipes?

Cheers
Muzza

I've used a VFR 400 header on one. The diameter was ballpark OK (larger) and the bends are in the right place. I had to slot the holes in the flange to suit the wider FXR holes.

May be a suitable pipe to build from if you happen to have one lying on the floor like I did.

**Muzzab** · 14th December 2011, 19:53

Originally Posted by koba

I've used a VFR 400 header on one. The diameter was ballpark OK (larger) and the bends are in the right place. I had to slot the holes in the flange to suit the wider FXR holes.

May be a suitable pipe to build from if you happen to have one lying on the floor like I did.

Thanks, heading over to CHCH to check out some wreckers probably best bet.

**motorbyclist** · 16th December 2011, 16:32

wanted: FXR/CBR/VTR front mudguard and/or front brakes (caliper-line-cylinder/lever)

**Ivan** · 19th December 2011, 15:29

anyone got a honda 125 ignition setup for cdi like stator flywheel and cdi?? my current bottom end is points and top end cdi and was hoping to convert it without going total loss

**motorbyclist** · 19th December 2011, 21:17

Originally Posted by Ivan

anyone got a honda 125 ignition setup for cdi like stator flywheel and cdi?? my current bottom end is points and top end cdi and was hoping to convert it without going total loss

two or four stroke? (does it matter?)

I've got some XL125 bits in the shed that might suit...

**Ivan** · 20th December 2011, 19:28

sorry should have said it is an xl125 its the old single piece head model, ive since converted the tope end to 2 piece xr200 head with a cdi setup but the bottom end is points

**Ivan** · 20th December 2011, 19:29

also thats a good question and i was wondering does it mator if the cdi stator is out of a 4 stroke or not?? like can a 4 stroke run a rm80 ignition with a 4 stroke cdi and coil?

**motorbyclist** · 20th December 2011, 22:26

Originally Posted by Ivan

also thats a good question and i was wondering does it mator if the cdi stator is out of a 4 stroke or not?? like can a 4 stroke run a rm80 ignition with a 4 stroke cdi and coil?

I dont see why not....

anyways, I've got a stator coil in unknown condition - XL125 1980-85ish looks like this one but with unpainted motor

**Ivan** · 21st December 2011, 15:56

Originally Posted by motorbyclist

I dont see why not....

anyways, I've got a stator coil in unknown condition - XL125 1980-85ish looks like this one but with unpainted motor

is that just the stator or do you have the flywheel as well?

**motorbyclist** · 23rd December 2011, 20:22

doubtful for the flywheel - I'm 95% sure I've still got the coil attached to cover somewhere in the shed but can't promise much else

**Henk** · 28th December 2011, 15:47

After a stock FXR header, just need the first stage skinny bit to make a pipe for a 100. I know I of all people should have FXR stuff coming out my ears but I've pretty much butchered all the ones I had for other bikes.

**kel** · 28th December 2011, 21:19

Looking for an FXR carb mount, just the rubber part. The cut down radiator hose isnt working for me. Cheers.

**gav24** · 5th January 2012, 11:22

I have a pair of gsx250 rims, 17 x 2.5 front and 17 x 3.5 rear. (with discs, sprocket, cush drive assy, and tyres (100 and 130)
Looking to swap for a pair of 17 inch RGV rims, or just the rear for a rear RGV rim. Looking for a 4, 4.25 or even 4.5 rear rim with the narrower suzuki rear hub, Late RGV ones I know fit but maybe you know that others do to GS500 maybe? 155mm from disc to sprocket, not the bigger ones that are 185 wide hubs.
Or any other decent motard rims for my DR650....What you got!

**Ivan** · 5th January 2012, 11:41

Originally Posted by gav24

I have a pair of gsx250 rims, 17 x 2.5 front and 17 x 3.5 rear. (with discs, sprocket, cush drive assy, and tyres (100 and 130)
Looking to swap for a pair of 17 inch RGV rims, or just the rear for a rear RGV rim. Looking for a 4, 4.25 or even 4.5 rear rim with the narrower suzuki rear hub, Late RGV ones I know fit but maybe you know that others do to GS500 maybe? 155mm from disc to sprocket, not the bigger ones that are 185 wide hubs.
Or any other decent motard rims for my DR650....What you got!

sent a message about my zzr rims