Bucket bits wanted & services needed

[richban]

Basically just after anything with a decent weight spring, so i can go straight on to the swingarm, instead using a linkage setup. This is for my RS50 frame.

I have a GSXR 600 shock I am going to put on trademe some time soon. Yours for 130. Come and get it.

[chrisc]

Asking here for a friend.

He's looking for a suitable 125 2 stroke engine for his FZR framed bucket to be. So GP125, TF etc, any suggestions or have something hanging out that may be of interest please contact me. Preferably in Auckland but may travel for something worthwhile. Muchas gracias

[koba]

Asking here for a friend.

He's looking for a suitable 125 2 stroke engine for his FZR framed bucket to be. So GP125, TF etc, any suggestions or have something hanging out that may be of interest please contact me. Preferably in Auckland but may travel for something worthwhile. Muchas gracias

Seen this?

http://www.trademe.co.nz/motors/moto...-425063632.htm

That crank looks pretty rusty. You are pretty much up for new bearings in any old shitter though, if you want it to last more than a few races.

[kel]

Does anyone have an older style (90's) Honda RS125 seat unit they would be willing to sell? Any condition considered, Cheers.

[Clivoris]

I'm after an exhaust end can that I can modify onto my DBS exhaust which is currently a little loud.

[F5 Dave]

Just drive it up to Damon (formerly known as Cycleworks, he'll sort it out ok. call him first.
04 526 2345
2019 Akatarawa Road,

[Clivoris]

Just drive it up to Damon (formerly known as Cycleworks, he'll sort it out ok. call him first.
04 526 2345
2019 Akatarawa Road,

Cheers Dave. I'm sure he'd do a great job but I'm thinking a little more budget than that. What I have in mind is something a bit munted that I could cut down as a temporary measure until I can sort something a bit prettier. Or an easy way to quieten down the can/cone I already have.

[Drew]

Seen this?

http://www.trademe.co.nz/motors/moto...-425063632.htm

That crank looks pretty rusty. You are pretty much up for new bearings in any old shitter though, if you want it to last more than a few races.

I hope he didn't take the picture of the slug as he assembled it. He's got it the wrong way around!

[koba]

I hope he didn't take the picture of the slug as he assembled it. He's got it the wrong way around!

Good spotting!

[SHELRACING]

Does anyone have a pair of Honda 125 twin header pipes they wish to part with.

Also looking for a good seat and tail unit. Something like the RS125 ones.

[Ivan]

anyone got any swing arms? mono shock ones

[Moooools]

Ahh yeah just got one off of a Hayabusa. Set up for a 360 section read tyre.
It is a monoshock so should fit right in.

$5 and it's yours.

[F5 Dave]

love your work max

[Racey Rider]

anyone got any swing arms? mono shock ones

I've got a couple of spare KR150 ones.

Could do a full, frame / shock / swing arm / rear 18" wheel / disk / and complete rear brake system if anyone needed such.


Heidenau do great 18" race compound rubber, so that's no issue.


Also.... while I'm, here.... ... RideLife has 2.75- 16" Heidenau race rubber in stock for those still running the smaller hoops.

Cheers.
Racey.

[Muzzab]

Probably a long shot, but does any one out there have an exhaust or even just a header pipe for a FXR surplus to requirements.
Failing that, any suggestions on any other suitable donor pipes?

Cheers
Muzza