Wiring for a Loncin [Archive] - Kiwi Biker forums

Mudflaps

6th May 2010, 21:14

So it seems I have cocked up my wiring after trying to make the connections better by changing them over into a new wiring block.

Anyone out there got a wiring diagram? I've got one of these http://newmanz.co.nz/shop/index.php?main_page=product_info&cPath=66&products_id=208 too, but without the plastic sockets as that is what was broken.

Ray LeCheminant

6th May 2010, 22:19

Just drop Shane from Newmanz a PM - he hangs about on this site a fair bit - normally in the Minimoto area

Kendog

6th May 2010, 22:57

Oh man, what have you done.
I drew a picture when I first wired it up, will see if I can find it.

Kendog

7th May 2010, 07:01

Found it.
The red wire connects to the plug, that help?

Mudflaps

7th May 2010, 07:22

Found it.
The red wire connects to the plug, that help?

Oh...so simple:)
Take it to work with you today and I'll give you a call at lunch time and write down the colour pairings. Had it running sweet the night before last too, but I had to tinker more didn't I!! I'm still planning on Sat morning.

Kendog

7th May 2010, 13:09

Oh...so simple:)
Take it to work with you today and I'll give you a call at lunch time and write down the colour pairings. Had it running sweet the night before last too, but I had to tinker more didn't I!! I'm still planning on Sat morning.
Sorry, I was almost at work by the time you sent that message.
I will text you when I get home.

Buckets4Me

7th May 2010, 18:11

Chinese CDI unit............

I sorry, I can't remember who was looking for a Chinese CDI wiring diagram so have posted it here. I expect the pin-out is much the same for all of them.

Thomas

http://www.kiwibiker.co.nz/forums/showthread.php/86554-ESE-s-works-engine-tuner/page150
bottom of the page dose that help ????

Mudflaps

7th May 2010, 19:27

http://www.kiwibiker.co.nz/forums/showthread.php/86554-ESE-s-works-engine-tuner/page150
bottom of the page dose that help ????

Holy cow!!!!... I think you have just saved me!! Awesome.

Thanks heaps, and make you next born bring you great wealth and prosperity!

Buckets4Me

7th May 2010, 21:45

Holy cow!!!!... I think you have just saved me!! Awesome.

Thanks heaps, and make you next born bring you great wealth and prosperity!

dont thank me thank Thomas
and if it blows up dont thank him

Mudflaps

8th May 2010, 17:10

The diagrams didn't help unfortunitly. All I really need to know is where the 5 wires need to go to from the cdi unit.

I have 2 greens, a red, a blue, a black and a yellow. Pretty sure one of the greens isn't used, if that helps?

TZ350

8th May 2010, 18:03

All I really need to know is where the 5 wires need to go to from the cdi unit.

I have 2 greens, a red, a blue, a black and a yellow.

Both greens are earthed, red to HV generator coil on the stator, blue to trigger pickup, black to kill switch, yellow to ignition coil.

Mudflaps

9th May 2010, 09:14

Kendog

10th May 2010, 06:48

THANKS!

Good news and bad news...
GOOD NEWS, I had all the wiring right
Bad NEWS, Still no spark??

I dug out the standard cdi unit and will try it out to rule out the racing cdi unit as the problem. I'll also go through and quadruple check and joins in the wiring.
I've re-wound the header coil wire into the spark plug cap, so that connection is fine. Earth connection is fine...What else??
This seems strange since it was going after your initial carb clean and wiring fix.
Have you tried the kill switch in both directions?
Have you tried a different spark plug?

Mudflaps

10th May 2010, 22:17

Yes and no.Yes I've tried the kill switch both ways and no I haven't tried a different spark plug. Maybe on Wed. Wed equals shed night!!

Trudes

11th May 2010, 07:04

Gotta get that thing going so we can hit the track...... I wanna see how much faster Rangi is than the Lonpoo now. ;)

Kendog

13th May 2010, 08:18

Maybe on Wed. Wed equals shed night!!
Did you get time to sort your bike?

fi5hy

13th May 2010, 18:05

I have heaps of CDI unit here mate. And yes they can shit them self often

Mudflaps

13th May 2010, 18:34

How much are you selling the cdi units for? But more importantly, is there any way of checking the unit itself to see if it is knackered?

Haven't done anymore with the wiring, but I have started to attach the new rear end. I have committed many sins that are lighter than the new tail piece!!