Results 1 to 8 of 8

Thread: JR50 not running right

  1. #1
    Join Date
    2nd October 2005 - 00:47
    Bike
    CR250
    Location
    Papamoa
    Posts
    3,993

    JR50 not running right

    I went to take my son for a spin on his 50 yesterday and it went like shit. It would only run with the choke on and only on full throttle.

    I got it second hand and it had sat in a garage for 15 years, so maybe a piston? thought you'd never do one in one of those... Jets are all clear, but I'll take the carb to work to clear it with the air compressor to be sure.

    Any other thoughts?

  2. #2
    Join Date
    24th May 2008 - 21:24
    Bike
    some honda bits in a kx chassis
    Location
    Waiuku City
    Posts
    1,326
    Iv seen a JR50 piston and bore that was scored to buggery, had the cylinder bored out .5mm, put an oversize piston in, including gaskets was ~$230.
    Otherwise it sounds like blocked jets somewhere. Not getting fuel so it needs the choke on all the time to richen what is getting through, and WOT is basically directly out of the float bowl so hard to block that.
    we may just go where no ones been

  3. #3
    Join Date
    22nd April 2009 - 19:57
    Bike
    2007 Yamaha WR250F
    Location
    Westharbour
    Posts
    219
    Blog Entries
    1
    Quote Originally Posted by cheese View Post
    I went to take my son for a spin on his 50 yesterday and it went like shit. It would only run with the choke on and only on full throttle.

    I got it second hand and it had sat in a garage for 15 years, so maybe a piston? thought you'd never do one in one of those... Jets are all clear, but I'll take the carb to work to clear it with the air compressor to be sure.

    Any other thoughts?
    only full throttle could be only on the main jet, pilot blocked,
    also only with choke usually means lean but you probably figured that
    i have seen them run in all sort of condition, got to be quite major not to run, they even run with f all compression and bags of piston slap
    Quote Originally Posted by Ktmboy View Post im gay i like men Quote

  4. #4
    Join Date
    2nd August 2006 - 22:17
    Bike
    hopefully bringing something back to NZ
    Location
    Hartford Connecticut USA
    Posts
    4,109
    our pw50 use to run but not the well was a little gut less new piston and rings and the thing is a whole new bike real quick (for what it is ) only prob i now have is needs new throttle cable its sorta stuck on full not the best for little kids.
    [SIGPIC][/SIG

  5. #5
    Join Date
    9th January 2006 - 12:26
    Bike
    KX450 Motard/Flat Track KTM150SX H2R
    Location
    Tauranga
    Posts
    4,444
    i would clean out the carb first and check the air filter is ok,

    if this does not help, then take of barrell off to have a look,

  6. #6
    Join Date
    17th July 2006 - 13:53
    Bike
    2006 CR250R
    Location
    Gisborne
    Posts
    2,090
    checked manifold-cylinder gasket or boot or whatever is there for leaks?

    wot & choke on a symptom of an air leak

  7. #7
    Join Date
    13th April 2005 - 12:00
    Bike
    Enfield cr250r
    Location
    Tokyo
    Posts
    3,429
    Blog Entries
    4
    Quote Originally Posted by B0000M View Post
    checked manifold-cylinder gasket or boot or whatever is there for leaks?

    wot & choke on a symptom of an air leak
    what he said , u can use brake clean to find the leak( engine note will change),,,, please don't launch yourself over the neighbors fence

    Stephen
    "Look, Madame, where we live, look how we live ... look at the life we have...The Republic has forgotten us."

  8. #8
    Join Date
    17th July 2006 - 13:53
    Bike
    2006 CR250R
    Location
    Gisborne
    Posts
    2,090
    Quote Originally Posted by Brian d'marge View Post
    what he said , u can use brake clean to find the leak( engine note will change),,,, please don't launch yourself over the neighbors fence

    Stephen
    i just read what i wrote yesterday... it almost looks like a barty post!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •