I think he was on the crack pipe between lap 2 and 3 the speed he went out atOriginally Posted by SVboy
This was lap 2, some random went past, then was fucking about, should have picked a better time to look over his shoulder
In the riders seat
I think he was on the crack pipe between lap 2 and 3 the speed he went out at
This was lap 2, some random went past, then was fucking about, should have picked a better time to look over his shoulder
"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough power."
No8 Wire Extraordinaire
One of the RM250 needle options is the NEDJ, works well in lots of bikes, perhaps find out what the RMX has in it and see what its running, if it has a smaller base diameter, could be worth a try. The only RMX I rode sounded a bit like that on small throttle openings.
Don't you look at my accountant.
He's the only one I've got.
In the riders seat
It's got whatever was factory in the PJ carb that came off it (most likely DGN, R1472L 1L), I just swapped internals into the PWK, I'm not fussy enough to care even though I know it is not 100 %
I know I've gone down a couple of main jet sizes and leaned it out one clip on the needle
"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough power."
Anorak
There was a special made for the mid 90's CR125 that works on a worn CR500 carb. i found one close i a carb i had here. It was night and day.
it has a real thick lower section.
Keihin needs a good kicking for not making the needle jet easily replaceable like a Mikuni
Yours doesn't sound as bad mine , it was like a 125 powerband to ride only 2.5 times the power. yours is still pretty smooth and linear sounding just fat sounding past the pilot
Kinky is using a feather. Perverted is using the whole chicken
Hardcore Biker
Lap one (video) is my sighting lap and picking the racing lines, lap two is me starting to loosen up, lap three and I'm good to go.
Sent from my SM-G960F using Tapatalk
flashg
Hardcore Biker
What can I say, Vicky had promised a nice meal (and it was awesome)
I also swallowed some beers when I got home.
Awesome day.
Sent from my SM-G960F using Tapatalk
flashg
Hardcore Biker
I thought I was slowing you down, so I twisted the throttle a bit more on the 300
Sent from my SM-G960F using Tapatalk
flashg
Hardcore Biker
https://youtu.be/HHPN_1go810
I'm not the fastest rider(getting old),but this is a full first lap of Sundays ride.
Sent from my SM-G960F using Tapatalk
flashg
In the riders seat
Lap one was a bit of a cock up, I missed a turn and while turning around I thought both Mike and Flash had gone past me, so I'm trying to catch Mike and Flash, while not realising Flash was still behind me
"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough power."
In the riders seat
You were on lap 3 ya cunt, I thought I was going to die trying to keep up with you, he was riding like a madman
"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough power."
Forum whore
Ride fast, Die young, stay pretty!
In the riders seat
Well Flash doesn't really qualify for any of those
Lap 1
"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough power."
No8 Wire Extraordinaire
Was that in the carpark? I have a Toyota.
It's just a bit of a jump down.
Don't you look at my accountant.
He's the only one I've got.
Una Storia Italiana
the FILTHY ONE.... hahahaha...
cheers DD
(Definately Dodgy)
No8 Wire Extraordinaire
Can't believe how sad and envious I am that I watched some of that.
Bike still sounds terrible. Blegbluur. Blegggbleeer. Rup..
Have you considered changing your mid valve shim- stack?
Don't you look at my accountant.
He's the only one I've got.
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote
Bookmarks