http://www.emgo.com/images/pdf/2017CONTROLS.pdf
Span adjustable might be a tough ask unless you change thev complete mc and complete clutch perch
http://www.emgo.com/images/pdf/2017CONTROLS.pdf
Span adjustable might be a tough ask unless you change thev complete mc and complete clutch perch
Good point. That thought hadn’t occurred to me, but HDC is wanting a twenty first century nicety for a twentieth century bike.
On checking the CRG web page they say they do levers for most modern sports bikes. I guess the job is possible but it might not be a simple fix.
There is a grey blur, and a green blur. I try to stay on the grey one. - Joey Dunlop
When I were a lad, the hot fix was "dog leg" levers - thats actually what I want. Span adjustable would be no good on this bike because you need to grab the thing with a hearty four finger grip and squeeze like a 13 year old who's just discovered masturbation.
Apart from EMGO, this crowd seems to do what I want: http://www.flandersco.com/Products.html Plus, their website is from about the mid 70's.
the levers arent a priority just a "nice to have" - the priority is investigating the front end.
Now all i need is a bit more co-operation from the weather gods.
I thought elections were decided by angry posts on social media. - F5 Dave
Ah I remember them I ran a set on by CB200.
Try Oldbikebarn.com
Or these guys who specialize in the smaller Hondas https://www.common-motor.com
Denniskirk.com used to have stuff like that when I had older Jap bikes - shipping will probably suck from them though.
went for a pootle today and I was like "Not loving that thud from the front..... must have lost a wheel weight". Yeah, not so much. The front rim is quite a long way out of true. If it needs a rebuild I will get someone to do it. I also decided to have a wee look at the forks. Big mistake.
Having said that the chrome sealing surface isnt too bad and they werent leaking. I think I will just clean them, put some paint on the really rusty bits and move on.
Hardest part was getting the top circlip out because it had sort of rusted into place. Icky
I thought elections were decided by angry posts on social media. - F5 Dave
Emulators. No one will see them.
Don't you look at my accountant.
He's the only one I've got.
Get a price from Franks Forks (Forking by Frank) in the USA. He's been producing standard, undersize and oversize fork tubes since the 60's
wonder what happened to my CB750 with the twin Dellorto side draught carbs, couldn't have been many like that around. Went well with the acellerator pumps and myriad of jetting.
Henry just a thought
I just brought some forks of a MG California these are 45mm and have adjustable damping comp and rebound
They are likely way to big for what i want and likely far to long and the spacing to wide
But they are perfect for what you have.
i mentioned earlier the 320mm brembo discs fit on your honda hub.I have one of the Brembos goldlines same as 748/916 etc, Pretty sure Kickaha has the other side. but these are pretty generic anyway 65mm mounts
The guy i brought them from said the tubes are pitted but the damage appears to be at the top which would be covered by the headlight.
I cant comment as i havent seen them yet.
The new tubes for these are $200USD each
edit loking at the chart even though honda have poxy small od front bearings and a small axel. 20mm axel on guzzi still only needs a bearing change 6002 to work with honda hub.
Easy stuff shouldnt be hard. I went to drop the oil out of it yesterday (doing it arse backwards as usual) - in fairness the oil didnt look too bad but I had bought a filter so I thought why not. No crush washers under either the oil tank drain or the sump plug drain... not even a flat copper washer. Oh, and the sump drain should be M12 x 1.5 x 12 long. Its some random UNF bolt cut to size. I suspect a PO has stripped it and just wound a bigger diameter bolt in there rather than helicoiling it. If it seals up with a copper washer I will leave it. If it doesnt I will do it properly.
Oh, and that front wheel? Radial and axial runout are OK (not quite within spec but not far). The fucking tyre has the runout. Either it isnt up in the bead lock or, errrrrr, something.
Gonna buy some bits on ebay (clocks and so forth) see if I can find a trustworthy American.
I thought elections were decided by angry posts on social media. - F5 Dave
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks