Here's the Stalker Laser spec sheet from their web site. Make your own mind up about error readings.Originally Posted by Lou Girardin
http://www.stalkerradar.com/pdf/lida...ifications.pdf
Applied Concepts, Inc. 2609 Technology Drive Plano, TX. 75074 Toll Free: 1-800-STALKER
Tel: 972-398-3780 Fax: 972-398-3781 sales@a-concepts.com http://www.a-concepts.com
006-0230-00 Rev L
S LIDAR SPECIFICATIONS
Operational:
Type: Handheld Lidar offering Tracking mode, Single Shot
mode, and Time/Distance mode.
Acquisition Time: Less than .4 second
Nominal Range : Minimum < 5 feet (1.5 meters)
Maximum > 4000 feet (1200 meters)
Range Accuracy: less than or equal to 1 foot (1/3 meter)
Speed Measure: ±1 mph to ±299 mph (±1.6 kph to ±481 kph)
Speed Accuracy: +1 mph, 2 mph (+1.6 kph, 3.2 kph)
Test/Alignment mode: Enter using the TEST key and the Trigger. Used to
test Hud alignment using audio tone.
Metric Operation: Setup menu selectable
Lidar trigger modes: Setup menu selectable:
1. Constant trigger depression for constant XMIT
2. Separate trigger depressions to start/stop XMIT
Time/Dist. trigger mode: Separate trigger depressions when target enters and
exits speed zone
Inclement Weather mode:Suppresses target returns from targets closer than
approximately 250 ft to reduce interference from rain,
fog, and snow
Remote Trigger: Remote trigger signal available through I/O Port
Target Speed Tone: Variable audio tone corresponding to target speed. A
fast target generates a higher tone and a slow target
generates a lower tone
Target Return Tone: No tone when beam is off target; tone repetition
increases as beam moves into target and return signal
quality increases
Switching Output: I/O Port signal for operation of external devices (i.e.: a
camera) Toggles when speed exceeds speed signal
setting
I/O Signals: Ext. Trigger, Switch Out, Tx, Rx, Gnd, and +5Vdc
Physical
Dimensions: 9.9 Height, 6.0 Length, and 4.2 Width
21.8 cm Height, 15.3 cm Length, 10.7 cm Width
Weight: Wt with Battery Handle - 3.8 lbs (1.72 kg)
Wt with Cigarette Handle - 3.0 pounds (1.36 kg)
Housing: Metal case with rubber end caps
Shoulder Stock: Accessory shoulder stock is available
Input Voltage Range: Battery Handle: 5.7V to 9.0V @ 400 ma. nominal
Low voltage inhibit activates between 5.7V and 6.2V
Cigarette Handle: 6.5V to 16.0V @270 ma. nominal
Low voltage inhibit activates between 6.5V and 7.2V
Low Voltage Inhibit: Inhibits all readings while input voltage is below the
low voltage inhibit level
Low Voltage Standby: After 10 seconds of inactivity (unit not transmitting),
power consumption is reduced to 63% of nominal
Input Power Protection: Solid state automatically resettable fuse
Environmental: -30 to +60 C, operating
-40 to +85 C, non-operating
Humidity Protection: +37 C, 90% Relative Humidity, 8 hours minimum,
operating
Additional Resistance: Dust, water, and impact
EMI: RFI icon indicates that the unit is in a high EMI field.
No false readings when the unit is subjected to
Electromagnetic Interference from vehicle alternator,
ignition, air conditioner/heater motor, windshield
wiper motor, Police FM transceiver, and Citizen Band
AM transceiver
Tripod Mount: Female Ό - 20 closed end nut on right side of case
I/O Connector: Standard 6-pin I.O. connector on right side of case
Transmitter & Receiver:
Operating Wavelength: 905 ± 10 nm Peak @ 25° C
Spectral Bandwidth: 5 ± 3 nm FWHM
Laser Type: MOCVD InGaAs Stacked Array Pulsed Laser Diode
Eye Safety: FDA/CDRH CLASS 1 Laser Device (Rated Eyesafe)
Pwr. Output & Density: TBD (meets FDA/CDRH regulations)
Pulse Width: < 30 nsec.
Pulse Repetition Rate: Fixed, 130 Hz (±0.1 % at 11.04 VDC)
Beam Divergence: < 3 ± 0.5 mrad FWHM
Optical Design Type: Bistatic (dual aperture)
HUD
Targeting: Illuminated Pinpoint, keyboard adjustable intensity.
Range and Speed Data: 7-Digit (7-segment) with ± LED display with keyboard
adjustable intensity
PANEL
Display: 8-Character (7-segment) with ± LCD display with
keyboard controlled backlight
Display Clear: Activates prior to new measurement (with depression
of trigger)
Power-On Self Test: Circuit elements tested, timing accuracy verified, and
all display elements illuminated. Errors indicated by
beep code.
Speed Display Lock: Manual control (auto lock of speed and range with
release of trigger)
Controls: Polycarbonate overlay covering backlit (with LEDs)
push button switches
SWITCH DEFINITION
TRIGGER: Setup Menu Selectable:
(Lidar mode) 1. Constant trigger depression for constant Xmit
2. Separate trigger depressions start/stop Xmit
TRIGGER: Separate trigger depressions when target enters and
(time/dist mode) exits speed zone
PWR: Rear Panel switch toggles main power ON/OFF
TEST: Performs a complete self-test
HUD Light: Toggles the HUD intensity from low to high through
six levels when pressed
SPEED/RANGE: Used to select Tracking mode, Single Shot mode,
Inclement Weather mode, and to toggle between
SPEED only, RANGE only, and simultaneous SPEED
and RANGE display. Used to exit from MIN, MAX,
and TIME/DIST modes.
PANEL LIGHT: Toggles both the LCD backlight and the keyboard
backlight ON and OFF
AUDIO: Used to adjust the volume of the speaker in 4 steps
TIME/DIST: Selects TIME/DIST mode
MAX: Used in TIME/DIST mode to display/update maximum
range
MIN: Used in TIME/DIST mode to display/update minimum
range
DISPLAY MESSAGES
Enn: This message indicates that a measurement error has
occurred
PASS: This message (with happy tone) indicates that a self-
test has successfully completed
Bookmarks