The KX stem is in the DR bottom clamp.
The bottom of the KX stem was a fraction of a gnats whisker smaller than the DR one so is held in by the spring clip and the bearing.
Sweet
Armature speller
The KX stem is in the DR bottom clamp.
The bottom of the KX stem was a fraction of a gnats whisker smaller than the DR one so is held in by the spring clip and the bearing.
Sweet
Armature speller
Coils/spark leads/caps and carb collector and airbox arrived today
Also looks like the GSX400S twin uses the same engine bolts/mounts.
terra firma rider
More more!!!
"The ultimate result of shielding men from the effects of folly is to fill the world with fools." - Herbert Spencer, English Philosopher (1820-1903)
www.AdventureRidingNZ.co. nz
Photos!
www.AdventureRidingNZ.co.nz NZ's dedicated Adventure Riding Community
Forums, free GPS track downloads and much more. Now over 5700 members, are you one of them?
Armature speller
Airbox and collector.
The carbs have to be removed to put the airbox/collector in!
The carbs themselves were a bit dirty/stiff/gummed up as expected.
The intakes have a bit of crud and could do with a bit of dremel sanding drum loving.
Armature speller
Butterflies are a bit gummed up. The throttle didn't even move...
Slides are a bit sticky. But all the diaphrams are in good nick..
Dunk it in CRC and open 'em up...
Float bowel is pretty good. looks like they just need a wipe with a rag and they'll be fine...
Not a lot visually wrong here...
Put them back together with a good CRC spraying and the slides move freely and the throttle opens with little effort and closes under it's spring tension.
Will need to check all the o-rings and jets but it looks to be in bloody good condition given it's history...
Armature speller
Makes the engine look a bit bigger too...
His Excellency
Bit of a tip for ya Fran. Tighten the airbox to the carbs first, then push the carb/box assy into the head manifolds. Old rubber is a bitch for slippin off. Said the preist to the vica.
Armature speller
Tracked down a CDI in Oz...
$A1114.00 plus postage
No thanks.
Hardcore Biker
Have you tried googling just the part number? That's how I got my CDI for NZ$270 landed (from the Netherlands) vs. 1k plus from Suzuki...Originally Posted by NordieBoy
www.AdventureRidingNZ.co. nz
ThreadJack
Nordie, seen this? http://www.geographx.co.nz/downloads.html
www.AdventureRidingNZ.co.nz NZ's dedicated Adventure Riding Community
Forums, free GPS track downloads and much more. Now over 5700 members, are you one of them?
Armature speller
GPS's and maps are covered in here too.
It's be difficult to threadjack this thread
"Geographx will not accept any liability for any inaccuracies or omissions, now will we give any undertaking to maintain the datasets below."
So will they or won't they?
www.AdventureRidingNZ.co. nz
I suspect thats supposed to be 'Nor will we....'GPS's and maps are covered in here too.
It's be difficult to threadjack this thread
"Geographx will not accept any liability for any inaccuracies or omissions, now will we give any undertaking to maintain the datasets below."
So will they or won't they?
I have a Colorado which will display 3D DEM data on the gps, but no one makes maps with it as the data appears to be hard to get. I wonder if that data is suitable.
www.AdventureRidingNZ.co.nz NZ's dedicated Adventure Riding Community
Forums, free GPS track downloads and much more. Now over 5700 members, are you one of them?
I aint bovvered
Maybe a stator in here
http://www.mysterywarehouse.com/
Armature speller
Went to do the air filter tonight as it's been a bit boggy off the bottom end for a little while and the filters clean dammit.
May be time to look inside the carb again.
Last time was 34,000km ago - 25/11/2008.
It's been running sweetly since then.
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote
Bookmarks