Boyles Dave now even i know that was later a Kawasaki dealer in Wellywood.Originally Posted by F5 Dave
Crasher used to work there didn't he?
Its high Street, Did you click on it 3 times?
Anorak
Boyles Dave now even i know that was later a Kawasaki dealer in Wellywood.
Crasher used to work there didn't he?
Its high Street, Did you click on it 3 times?
Kinky is using a feather. Perverted is using the whole chicken
No8 Wire Extraordinaire
Yeah High Street I walk most days. Certainly dont walk hutt road. Slip of the finger.
There have been several Boyles in wgtn. Dickie Boyle who reputedly was a 2 stroke tuner of merit. I remember Lawton&Boyle. And of course the current Mark and John Boyle but I rarely get into that end of town.
But everything thing else is before my time.
Sadly High Street place- it appears to be a TAB now.
Don't you look at my accountant.
He's the only one I've got.
Anorak
So they lanced the Boyles.
http://www.wandtattoo.de/bilder/inha...-wettkampf.jpg
Kinky is using a feather. Perverted is using the whole chicken
No8 Wire Extraordinaire
And another reason to dislike people. Strip engine time. Hmm some cases bolts are loose. Or mullered. Or not original.
There had been little engine oil. Taking out the drain plugs there was one hollow one. Ahh detent for gear shifter barrel, but with no bb or spring. No wonder they had been fooling with the covers.
Oil pump off. ERM what's this odd bit of hand made steel? Trying to drive the pump.
Oh goody. Clear RTV oozing. Filthy.
Mmm that looks nice huh?
Crank looking ok but will be rebuilt anyway. Mains are bstd sizes. And very obsolete I have been warned.
Otherwise I'm totally at home with the Suzuki architecture that is RG50 ancestry written all over it with some TS and horizontal split that the singles obviously don't have. I've zip bagged all the bits
To be sure I don't mix them.
Do need to match and clean some outside bolts for zinc plating but I have a whole other engine to fish from.
Found a place in Texas that listed the bearings and some other stuff complete with prices. Long story short after a call it appears that the site is not listing NOS that they actually have.
Don't you look at my accountant.
He's the only one I've got.
Bogeyman
Frank Boyle, shop was in Lower Hutt. Same family as Lawton Boyle in Wgtn I think.
Frank rode speedway, two boys rode MX, lived up on the western hills, had their own practice track up there. All gone.
Go soothingly on the grease mud, as there lurks the skid demon
Low personal B.M.E.P.
Post the bearing sizes and numbers if you can still see them, Dave. There's an independent bearing house here in ChCh who have found REAL oddities for me before. If you think you've got problems, try and find Rudge main bearings...this outfit did, bought up what they found for me and now have pretty much cornered the market for Vintage size bearings.
Anorak
15 CRANKSHAFT BEARING 20x52x17 PART OBSOLETE
17 RH CRANKSHAFT BEARING 20x52x14 PART OBSOLETE
23 CRANKSHAFT BEARING 20x52x17 PART OBSOLETE
27 RH CRANKSHAFT BEARING 20x52x14 PART OBSOLETE
Can bearing be thinned one mm.
09269-20005 $10.00 http://www.speedsupplies.com/parts/s...9269-20005.htm
09262-20028 $20.43 http://www.speedsupplies.com/parts/s...9262-20028.htm
http://www.suzukiofvannuys.com/fiche...1971&fveh=1932
If you search under the Suzuki part number there is some scatered arround the world Start with USA first, They don't fix stuff they park it.
TS75 BEARING 20x52x14 09262-20005 $17.35
http://www.mrcycles.com/oemparts/a/s...ton-crankshaft
Kinky is using a feather. Perverted is using the whole chicken
Low personal B.M.E.P.
So it's the bearing widths which is the problem...well there's ways round that.
No8 Wire Extraordinaire
And it just goes on. Pop quiz. What is this part that I found in the spares? Bearing in mind that the spares are the bottom end assortment of a T90.
Give me a minute. . .
Don't you look at my accountant.
He's the only one I've got.
No8 Wire Extraordinaire
Anyway its pretty clear. This isn't the first engine I've bought that the last master mechanic has considered that the crank seals were unnecessary optional extras.
Sheesh. I hasn't noticed as I've yet to take the rotor off, just need to borrow or buy something with an M16 1.5 thread. Of the 4 pullers I have, of course. . .
Don't you look at my accountant.
He's the only one I've got.
No8 Wire Extraordinaire
Thanks Husa, but if you read the disclaimer. . .
Description
Part Number 09269-20005
$10.00
Suzuki Part Number Options
09269 20005
0926920005
SZ-09269-20005
* All parts sold and priced individually. OEM replacement part availability is subject to that of the manufacturer's stock. They are special order. No New Old Stock items available. Please see our parts diagram sections and Quick Entry Screens for further selections.
Copyright © 2015 Speed Supplies. All rights reserved.
That means they've loaded up some data but order everything from US Suzuki and hope for the best.
Don't you look at my accountant.
He's the only one I've got.
No8 Wire Extraordinaire
I spoke to the chap selling the one on TM he thinned bearing but found some more. Also need to be bored for pins. I know a good toolmaker so anything is possible.
Don't you look at my accountant.
He's the only one I've got.
Anorak
Details Aye this one seems to work
http://www.mrcycles.com/oemparts/p/s...-20005/bearing
Well they seem to be in stock it adds to Kart
Kinky is using a feather. Perverted is using the whole chicken
No8 Wire Extraordinaire
Yeah did at action sports as well, even got to PayPal before I got suspicious. They'd take your order. The guy on the phone was a bit surprised that I'd be trying to order parts that old, but insisted he'd try for the list I later emailed him.
Don't you look at my accountant.
He's the only one I've got.
Anorak
A-holes whats the point of saying its stocked if its not, other than to take your money.
Kinky is using a feather. Perverted is using the whole chicken
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote
Bookmarks