Scottoiler

[Naki Rat]

This is my weekend project. Which position is actually the "prime" position?

Plenty of information on their site.

[Gremlin]

This is my weekend project. Which position is actually the "prime" position?

You should be able to see numbers around the top of the reservoir. The lower the number the slower the drip rate. Prime is past the top of the numbers, and you simply rotate the cap so that the indicator tab is hovering over the desired setting.

How can I actually tell that the chain is being oiled by it?

It will look oily

[p.dath]

Spoke to a friend about using a Scottoiler and he told me not to bother as they are messy. But with all the positive comments on here decided to give it a try anyway.

Seems okay. I tend to let my bike warm up on the drive way before using it. When the bike is on its side stand the oil drips onto the ground. I get a nice little blue patch.

What do others do about "the leak"? Just tolerate it?

[Naki Rat]

Spoke to a friend about using a Scottoiler and he told me not to bother as they are messy. But with all the positive comments on here decided to give it a try anyway.

Seems okay. I tend to let my bike warm up on the drive way before using it. When the bike is on its side stand the oil drips onto the ground. I get a nice little blue patch.

What do others do about "the leak"? Just tolerate it?

If it is fitted correctly it shouldn't drip. The vacuum of the inlet manifold (or similar) feed starts the oil feed but with the engine stopped the lack of vacuum should shut it off.

[p.dath]

If it is fitted correctly it shouldn't drip. The vacuum of the inlet manifold (or similar) feed starts the oil feed but with the engine stopped the lack of vacuum should shut it off.

Let me clarify. I start my bike. It's leaning over because it is on its side stand warming up. Because it is leaning over the oil drips on the outside of the chain and onto the ground.

When the bike is vertical all is well.

[bsasuper]

For me, the scottoiler is a very expensive mess maker, chain wax used every few hundred k's is fine.

[LBD]

It should be point more down, towards the chain links, ie, simple theory. You don't need to oil the sprocket, you need to oil the links in the chain...

Oiling against the sprocket is is fine, centrifugal force spreads it onto the chain.

I was going to fit a Scottoiler but was unable to locate a discrete location...so I now put a little dribble on either side of the the sproket when I fuel up. One tension in 5500km was enough...chain is greasy not oily...all good IMO.

[Naki Rat]

Let me clarify. I start my bike. It's leaning over because it is on its side stand warming up. Because it is leaning over the oil drips on the outside of the chain and onto the ground.

When the bike is vertical all is well.

Adjust the outlet so it drips where the oil is required. I suspect that you should also back the flow off a tad. I have no such problem, just a permanently lightly (but sufficiently) lubed chain

[p.dath]

My experience with my scottoiler is about 50/50 after using it for a couple of weeks now.

I have it set to drip every 45s. When I started using it two weeks ago I gave the chain a clean as well.

I've noticed if I go somewhere and park the bike for a while, say 8 hours or so, when I come back there are always a couple of black puddles of oil on the ground under the chain along the length of the chain. Not big puddles, but noticeable. It is definately coming from the chain.

When I was simply greasing my chain I didn't get any oil spots. I think the chain lube sticks to the chain much better.

So is this fairly normal for a scottoiler, or should I back the flow off even more?

[bsasuper]

problem with using oil is everything sticks to it, chain waxes tend to leave a dry film.

[Jantar]

Unless you are riding gravel or wet roads then 1 drop per minute is all that is required. On long rides in warm conditions (oil flows faster when warm) one drop per 90 seconds is all that is required.

[nallac]

Don't have one myself, but it definately sounds like its getting over oiled
if its dripping alot of oil after sitting for a while.

I clean and oil the chain myself,stays hell of a lot cleaner than lube but would prefer a scott oiler.Sooo much easier............

[tuska]

is scott oil that special...surely all o ring chains are oil resistant anyway...wouldn't a thick oil do job for much less per litre?

[p.dath]

For me, the scottoiler is a very expensive mess maker, chain wax used every few hundred k's is fine.

After using the Scott Oiler for about 3 weeks now I have decided to stop and go back to use normal chain lube.

Even after adjusting the flow rate right down it still proves to be a mess maker.