The 50

[TALLIS]

have not bid , if was the right price maybe

No no... 50's are suppose to have cams, lots of cams.

[mr bucketracer]

No no... 50's are suppose to have cams, lots of cams.

i guess they should

[lodgernz]

air cooled ones ? do you have a link?

I was thinking of Polini and Malossi. They both do air-cooled and water-cooled RD/DT cylinders, but I suspect they were all big-bore.
Maybe you could make a fast RD70 or 80?

[sonic_v]

air cooled ones ? do you have a link?

Here's a standard one.

http://www.ebay.co.uk/itm/NEW-CYLIND...MAAOSwHQ9WV1pV

[dark art]

Airsal also makes a good alu/nikasil 45mm cylinder.
I´m sure you can find it a lot cheaper:

http://www.racing-planet.co.uk/cylin...l#.Vw8qyXr9ldg

[TALLIS]

My new Mickey mouse 50

[mr bucketracer]

My new Mickey mouse 50

make it a hundy and we are 4 stroking

[TALLIS]

make it a hundy and we are 4 stroking

It's in the mail

[Grumph]

Many moons ago there was a real CR110 Honda 50 in NZ. Dale Wylie picked it up in Malaysia for Bob Harris in ChCh. I think Dale won a NZ50cc GP on it at Ruapuna. Long since sold to an overseas collector.

[cotswold]

Can any one give me the cylinder stud spacings for their water cooled 50's, I have a project engine I am playing with and it has a 70 kit I want to ditch and replace with a 50, mine is case reed with studs spaced square 52mm

[husaberg]

Can any one give me the cylinder stud spacings for their water cooled 50's, I have a project engine I am playing with and it has a 70 kit I want to ditch and replace with a 50, mine is case reed with studs spaced square 52mm

Google told me
http://www.mopedarmy.com/wiki/Moped_..._stud_spacings

he told me this too
http://www.apriliaforum.com/forums/a.../t-242814.html

Useless factoid is the XR200 and 125S and H100/MB100 all have the same stud spacing's.
I have no idea why...........
If anyone does please write the reason on a $20 note and post it to me.

[cotswold]

[QUOTE=husaberg;1130966954]Google told me
http://www.mopedarmy.com/wiki/Moped_..._stud_spacings

he told me this too
http://www.apriliaforum.com/forums/a.../t-242814.html



http://www.mopedarmy.com/wiki/Moped_..._stud_spacings

Cheers Husa but this only tells me what wont fit , I already found that one. I was hoping that the Aprilia RS had the same spacings and one of our Euro friends confirmed it for me

[richban]

So it it an AM6 engine Tim?

I have just started getting my 50 into engmod. A few lessons already. My reeds don't have enough area to make the power I want. Also pipe needs a small adjustment. But that timing of 192 / 130 is hard to beat.

[cotswold]

So it it an AM6 engine Tim?

I have just started getting my 50 into engmod. A few lessons already. My reeds don't have enough area to make the power I want. Also pipe needs a small adjustment. But that timing of 192 / 130 is hard to beat.

No Rich it's a cvt project, I have on the plans

[richban]

No Rich it's a cvt project, I have on the plans

Yuck. Gears are the future. I can see the advantages. I have raced an auto scooter, its a different ball game as far as riding goes. My advice is look into rear bake systems that will give max control. Its all about the rear brake to tip in and keep mid corner stability. But after that its all a bit boring. Fast boring though.