For sale: vfr400r nc21 unfinished project

[Disco Dan]

Couple more pics for you all......

[FilthyLuka]

[QUOTE=skidMark;1305485]

just one of the bolts for the sprocket cover (while holds hydrolic clutch caliper) is snapped of in the hole in the crankcase that it goes into...bolt needs to be drilled out and hole retapped..../ helicoil put in.

Mate, doesn't even need that. Just drill a small hole and use a stud extractor, good as new

[skidMark]

[quote=FilthyLuka;1305589]

Mate, doesn't even need that. Just drill a small hole and use a stud extractor, good as new

yeah easy out would do it...but sometimes they snap and if an easy out snaps it makes it damn hard to drill out as they are hardenered lol....easy out becomes a ...not so easy out....learned that the hard way. on a mini chopper once lol

[koba]

Interested in the bike in my profile?
Its an NSR250 frame with a 600 single jammed up it.
Nutcase bike.
It's changed a wee bit since that photo, it now has a fibreglass monocouque(sp?) tailpiece, 2 extra braces, re-engineered exhaust mounts and UHMWPE crashbungs.

Needs new clutchplates. (goes but slips when hot)
Its a bitch to start (needs rollers)

Does big wheelies, current gearing too low for manfield but perfect for taupo short. Would probably cream a 400 round there given equal riders as it has far more instant pickup, in one of the higher gears I let of the throttle as the race was red flagged and It held close to a hundie kays at idle!

Lighter than my rg 150

I have an NC21 aswell and could probably do with a pile of spares or trackbike. Mines a wee bit 2 tidy to race at the moment, altho that may change if i scratch it up

[ambler]

i hope you have more than just a hammer to work on the bike with

[skidMark]

Interested in the bike in my profile?
Its an NSR250 frame with a 600 single jammed up it.
Nutcase bike.
It's changed a wee bit since that photo, it now has a fibreglass monocouque(sp?) tailpiece, 2 extra braces, re-engineered exhaust mounts and UHMWPE crashbungs.

Needs new clutchplates. (goes but slips when hot)
Its a bitch to start (needs rollers)

Does big wheelies, current gearing too low for manfield but perfect for taupo short. Would probably cream a 400 round there given equal riders as it has far more instant pickup, in one of the higher gears I let of the throttle as the race was red flagged and It held close to a hundie kays at idle!

Lighter than my rg 150

I have an NC21 aswell and could probably do with a pile of spares or trackbike. Mines a wee bit 2 tidy to race at the moment, altho that may change if i scratch it up

really would prefer the dosh to be honest but will have a think on it but answer is a no at this stage, it is very nice though.....

tempting lol

oh andi forgot earlier but the vfr has no throttle cables...fully slipped my mind... so yeah sorry all

another thought is i may part it out?

i don't know how much demand thier is for bits though.

[Disco Dan]

the vfr has no throttle cables...fully slipped my mind... so yeah sorry all

ahhh so it was your cable I used to make my number plate flip up

"my bad"

[skidMark]

ahhh so it was your cable I used to make my number plate flip up

"my bad"

you bastard LOL

[skidMark]

one of you lot better buy it soon...

gotta make way for me new toy

[EJK]

Hammer is all I need to fix it up?
Referr to the pic

[Disco Dan]

Hammer is all I need to fix it up?
Referr to the pic

Oi, thats my hammer your talking about!

hmmm at least he cleaned my driveway after doing his bike


Good luck with the sale bud, my advice? Pull her to bits and sell each one on trademe. You would probably be able to get more money for it selling it as 'a bike'. Thats what I would do.

[westie]

I may be interested in parts off your bike.

[SwanTiger]

$200.00 Actually make that $150.00, just remember you still owe me $50.00

Only want the engine for my gokart.

[skidMark]

I may be interested in parts off your bike.

would prefer not to part it out

and swantiger...if u want one of these motors from a wrecker...they are 800 without loom.

so no keep dreaming considering it's the most valueable part of the bike.

[westie]

would prefer not to part it out

and swantiger...if u want one of these motors from a wrecker...they are 800 without loom.

so no keep dreaming considering it's the most valueable part of the bike.

Sorry to screw you over mark.

Swantiger there is a vfr 400 motor for $400 with all the goodies ie electrics and radiators.. What are you after???