Bucket bits wanted & services needed

[RDjase]

bout the ax100. i knew i had to be quick but hell. haha was just wantin it to replace the 1st bike i build up myself. but i didnt know they where so popular on here. hahaha if there is anyone else out there with a ax100 or something similar and they wanna get rid of it cheap message me.

Heres a new engine

http://newmanz.co.nz/shop/index.php?main_page=product_info&cPath=1_5&products_id=164

[RideLife]

anyone got any fork springs at all?

I've got a couple of KR150 fork springs spare if they're any good for something.

Racey.

[ac3_snow]

If you want to the OKO off my bucket let me know. As long as I have it back by the 13th it's all good.

yus please! will be in touch

[Ivan]

I've got a couple of KR150 fork springs spare if they're any good for something.

Racey.

Hey racey they would be probably what I am after

[koba]

I'm on the lookout for a master cylinder to suit a single front brake setup.

[motorbyclist]

I'm on the lookout for a master cylinder to suit a single front brake setup.

so what piston diameter would that be?

[koba]

so what piston diameter would that be?

852 piloklegs

[Gigglebutton]

Has any one got or know where i can get a Rm80 or Rs125 shock to fit my Rg50
Dazz

[Dutchee]

As you're mentioning RM80 and Team ESE had mentioned KX80, I thought I'd throw a link to a CR80 shock in the mix:
http://www.trademe.co.nz/Trade-Me-Motors/Motorbikes/Parts-for-sale/Suspension/auction-373415836.htm
lol

[ac3_snow]

Does any one have on old set of TF 125 rings? I'm after an old standard set 56 56.5 maybe even 56.75 mm think the GP's are the same, don't care how old or worn they are just want some old ones to slap something together.
want them for this weekend so someone in auckland???

[Rick 52]

Will bring them on Suday ..

[motorbyclist]

what's on this weekend?

[Pumba]

what's on this weekend?

your a week out

[Dutchee]

there's a Waitemata club family day at woodhill,not sure what else is on though. Superbikes is on the following weekend, and moto gp is also having a break. Junior masterchef's on prime on saturday and we've got a dinner to go to.
I guess there will be trailrides on around the country, maybe some racing somewhiere, I dunno. Buckets was last weekend.
Oh, on Four is blackhawk down at the moment.

Oh, if you really have nothing to go to, the MNZ AGM's on in Palmerston. That's about the limit of what I know is on, but it's impressive I know that much.
hahaha (sorry for not quoting post above Pumba's - being lazy)

[Arronduke]

I would very much like to borrow a carb that is of similar size and shape to a 24mm OKO/KEIHN flatslide.

I have one on its way (or not and i got scammed $700) but in the meantime I am trying to mount my engine. As there is not much room to play with in the carb vicinity, I would like to check clearances etc before I commit to making the mounts.

No... must be a mistake... $700 notes... I purchased my OKO carb.. landed for just over $100... maybe you brought half a doz... and got a bulk discount..:shutup:

[Moooools]

Has anybody got a 15mm wheel axle that is at least 250mm long? Needs to 'standard' type. (Bolt head on one end and thread on the other)

A TZR 1KT rear axle would work...

Max

[Henk]

Had a few wines and too lazy to go and look right now.
Any idea if either GSXR250 or Impulse axles would work and are you after front or rear?
Just read your post again. That would be rear.

[Moooools]

I have no idea if they would work. If you could measure one up it would be good.

It doesn't matter if it is front or rear, just that it is 15mm and over 250mm long.
15mm is the same diameter as an FXR front axle...

[Slingshot]

Has anybody got a 15mm wheel axle that is at least 250mm long? Needs to 'standard' type. (Bolt head on one end and thread on the other)

A TZR 1KT rear axle would work...

Max

TZR real wheel in a RGV frame per chance?

[Moooools]

TZR real wheel in a RGV frame per chance?

No. Try RS 125 front wheel in zxr 250 forks in tzr frame. The zxr forks have a 20mm axle so I am having to do some adaptation. The axle is going to be modified so it doesn't really matter what it is off.

[Henk]

I'll try and remember to have a look over the weekend, not gaurantees, alzheimers

[Henk]

I'll try and remember to have a look over the weekend, no gaurantees, alzheimers

[Henk]

I have no idea if they would work. If you could measure one up it would be good.

It doesn't matter if it is front or rear, just that it is 15mm and over 250mm long.
15mm is the same diameter as an FXR front axle...

15mm x 305 do? GSXR250 rear axle.

Sorry about the double post above, these things can happen when you drink your dinner.

[Henk]

Looks like I'm going to need a sprocket carrier so if anyone has one to spare let me know.

[Racey Rider]

http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/wheels/auction-381667060.htm
That's me selling a 4x17" rear rim with disk if it's of use to anyone?
$120 through KB.

[Moooools]

Apparently these are extremely heavy. So not much good for a bucket.

[Gigglebutton]

I have bought a motor in Timaru and need to get it to Auckland. I have been quoted nearly a $100 freight, from Main Freight, which almost as much as i paid for it. Does anyone know of a cheaper option. Dazz

[Yow Ling]

I have bought a motor in Timaru and need to get it to Auckland. I have been quoted nearly a $100 freight, from Main Freight, which almost as much as i paid for it. Does anyone know of a cheaper option. Dazz

can you get it to chch?if you can i can send to you for around $20

[Gigglebutton]

can you get it to chch?if you can i can send to you for around $20
Thanks. I will see what i can do :yes:

[gav]

Whats the motor? How big? Racing at Levels on the 18th, might be someone that can pick it up for you?

[Gigglebutton]

Whats the motor? How big? Racing at Levels on the 18th, might be someone that can pick it up for you?

Ke125,carb airbox and coils. maybe 10kg dry. That would be good if you could. Michele & Henk could grab off you there. Dazz

[Dutchee]

lol, no, we're heading to Kaitoke that weekend, not levels unfortunately :(

[grantnz]

Looking for one of these to match RS tailpiece. With original mounting points.

[jaffaonajappa]

Looking for one of these to match RS tailpiece. With original mounting points.

Your RS Tailpice matches that...and has mounting points.?
Something your not telling us? :P

[Dutchee]

Looking for one of these to match RS tailpiece. With original mounting points.

Male or female version? Talk to Arron, he's sick enough to have something like that (good paint scheme for after he wads it up haha)

[gav]

Anyone got a spare coil for a Suzuki GT125 twin?

[Arronduke]

Male or female version? Talk to Arron, he's sick enough to have something like that (good paint scheme for after he wads it up haha)

Thats cool.... but whats she doing wearing a g string? ... potental piviot point...:gob:

[ajturbo]

Anyone got a spare coil for a Suzuki GT125 twin?

i think i have.... but i would just get a better one.....?i'm away this weekend, but i'll check for you next week.. PM your address
AJ

[Kickaha]

I have bought a motor in Timaru and need to get it to Auckland. I have been quoted nearly a $100 freight, from Main Freight, which almost as much as i paid for it. Does anyone know of a cheaper option. Dazz

Should be getting picked up tomorrow


can you get it to chch?if you can i can send to you for around $20

I'll drop it off to you next week

[Gigglebutton]

Should be getting picked up tomorrow



I'll drop it off to you next week

Thanks to every one that offered to help. Hope i can return the favor one day :2thumbsup:

[Bender]

Has anyone got a Honda CB125 carb for sale? Would like to try a new one on my bike.

Edit: Got one thanks.

[kel]

Im after an FXR150 air box, any old condition will do. Cheers

[Gigglebutton]

Im after an FXR150 air box, any old condition will do. Cheers

I have one from a John Deer that might fit :laugh:

[boostin]

Im after an FXR150 air box, any old condition will do. Cheers

I got one in Albany mate, welcome to it.

[Trudes]

Anyone in the Wellington area with a welder able to help me out?
Rangi's top engine mount has cracked. It either needs a new bracket doctored up or the cracks welded up. I don't have a welder and am pretty shithouse at welding, but I am a fairly decent baker/cook, can buy a mean couple of dozen beer and give shithot hugs for payment of favors..... :D
Chur.

[GirrlRacer]

Anyone in the Wellington area with a welder able to help me out?
Rangi's top engine mount has cracked. It either needs a new bracket doctored up or the cracks welded up. I don't have a welder and am pretty shithouse at welding, but I am a fairly decent baker/cook, can buy a mean couple of dozen beer and give shithot hugs for payment of favors..... :D
Chur. have you tried asking skunk?

[jaffaonajappa]

I am a fairly decent baker/cook, can buy a mean couple of dozen beer and give shithot hugs for payment of favors.

:buggerd::drool::lol:
:beer::calm:

damn, luvin these icons :)

[Trudes]

have you tried asking skunk?

Poor Skunk is always getting stuck helping me, and I feel stink asking him to help me again when he normally has HEAPS of other stuff he's busy doing, including fixing his own bucket.

[saxet]

Poor Skunk is always getting stuck helping me, and I feel stink asking him to help me again when he normally has HEAPS of other stuff he's busy doing, including fixing his own bucket.

If you get stuck I've got a mate just up the road with a mig welder, if you want to bring it out to the Hutt.

[all4A50s]

Anyone in the Wellington area with a welder able to help me out?
Rangi's top engine mount has cracked. It either needs a new bracket doctored up or the cracks welded up. I don't have a welder and am pretty shithouse at welding, but I am a fairly decent baker/cook, can buy a mean couple of dozen beer and give shithot hugs for payment of favors..... :D
Chur.

Sorry just saw this. If your still need help PM me, my mig and I are available this weekend.

[Trudes]

Anyone in the Wellington area with a welder able to help me out?
Rangi's top engine mount has cracked. It either needs a new bracket doctored up or the cracks welded up. I don't have a welder and am pretty shithouse at welding, but I am a fairly decent baker/cook, can buy a mean couple of dozen beer and give shithot hugs for payment of favors..... :D
Chur.

All sorted, thanks Malcolm! :D
Damn, that's some tidy welding :niceone:

[Arronduke]

Cool thing with the welding... a perfect display of bucket racers helping each other... 10/10

Now who can help me...?
Want my FXR to produce 27hp... and cost FA...sorry can't bake... actually can't do FA... but my wife... she can clean....

[Henk]

Now who can help me...?
Want my FXR to produce 27hp... and cost FA...sorry can't bake... actually can't do FA... but my wife... she can clean....

Why? until you learn to ride more power won't help

[Arronduke]

You might be correct ... maybe i should start idolizing some one else... since I started coping your style my lap times have gone down... and the pit girls stopped asking for my autograph...

Note... need new mentor... Kevin Schwanz did FA for my road riding skills..... seemed to crash all the time.

Just read the book Croz... very good... anyone know his number?

[jaffaonajappa]

You might be correct ... maybe i should start idolizing some one else... since I started coping your style my lap times have gone down... and the pit girls stopped asking for my autograph...


Down?
Or Up? lololol

[Pumba]

Cool thing with the welding... a perfect display of bucket racers helping each other... 10/10

Now who can help me...?
Want my FXR to produce 27hp... and cost FA...sorry can't bake... actually can't do FA... but my wife... she can clean....

Surething Arron we can get started on your bike just as soon as your wife starts at my place. Bacon and eggs for breaky tomorrow would be great, and then once she has cleaned up the dishes she can move onto cleaning the rest of the house. I will get not designing and building that engine for you right away honest

[jaffaonajappa]

ohhhh. hmmm.
can i ask anyways?

Is she cute?

[Ivan]

anyone ended up with any rims that are 120 front and like 150 rear? this is for a motard but thought possibly some bucket guys might have aquired some in the corner somewere 17 inch to

[quallman1234]

anyone ended up with any rims that are 120 front and like 150 rear? this is for a motard but thought possibly some bucket guys might have aquired some in the corner somewere 17 inch to

Got some ZXR250 rims here. Did i tell you?

2 Front Discs (I think they are mint)
1 Rear disc

3" x 17" Front Rim
4" x 18" Rear Rim (Who cares if its a 18" you can still get good tyres and it makes fuck all difference)

They have almost brand new GPR10a's (soft compound awesome tyre) on them - 500ish a set alone.

500$ Firm.

[Ivan]

I actually got a set of 17s yesterday

[quallman1234]

Sweet! I'm tempted to motard my KDX but its a bit slow apart from say a tight kart track like roys hill

[Ivan]

im looking into trying to get a Wellington series going some street races slipway etc

[ajturbo]

im looking into trying to get a Wellington series going some street races slipway etc

Cool.. talk to Skunk or fish.... they should be able to advise...:woohoo:

[rabidnz]

im after a cylinder , head, and a set of pv's for an rg 150 im workin on at the moment, as nice as condition as possible, if anyone has them lying around, or could point me in the right direction please dont hesitate to flick me a pm at your closest convenience :drinkup:
Cheers!

[Arronduke]

I am after a light bulb from a FXR dash... come on you lot... there must be heaps in your sheds wanting a new home... hell only want one... that goes!!!

[Slingshot]

im after a cylinder , head, and a set of pv's for an rg 150 im workin on at the moment, as nice as condition as possible, if anyone has them lying around, or could point me in the right direction please dont hesitate to flick me a pm at your closest convenience :drinkup:
Cheers!

Here's a cylinder (http://www.sella.co.nz/motoring/motorcycles-scooters/parts-for-sale/complete-engines/86vbh5/).

[Henk]

I am after a light bulb from a FXR dash... come on you lot... there must be heaps in your sheds wanting a new home... hell only want one... that goes!!!

You can take one out of my bike at the next meet if you like. Of course if I see you taking it I'll attempt to beat the living hell out of you.

Edit
Why don't you just use one of the indicator bulbs or high beam from your own dash, or have you already got those hooked up to unneccesary idiot lights?

[captain hopeless]

Wanted - bucket motor, going in to an MC22 CBR frame. 200-300 dollars. Anything out there in Auckland?
Andy

[Bren_chch]

Wanted - bucket motor, going in to an MC22 CBR frame. 200-300 dollars. Anything out there in Auckland?
Andy

hey, i have a mint ts125 motor, new rod and piston. u can have for 300, comes with all electrics, no carb. 20bucks will cover courier.

[Arronduke]

You can take one out of my bike at the next meet if you like. Of course if I see you taking it I'll attempt to beat the living hell out of you.

Edit
Why don't you just use one of the indicator bulbs or high beam from your own dash, or have you already got those hooked up to unneccesary idiot lights?

The shame of it all.... all mine are rooted except one... on the left side of my dash... it powers up with the on switch is turned on... need another to even it up.. make it purfect..!

[Henk]

Let me get this straight. You need not one, but two idiot lights to tell you that you have turned the bike on? :facepalm:

[cotswold]

You need not one, but two idiot lights to tell you that you have turned the bike on? :facepalm:[/QUOTE]

Can I get one for her indoors?? it would save a whole load of time & aggravation

[Yow Ling]

The shame of it all.... all mine are rooted except one... on the left side of my dash... it powers up with the on switch is turned on... need another to even it up.. make it purfect..!

Send $50 , I send you complete FXR dash you can take a bulb out of it

[koba]

The shame of it all.... all mine are rooted except one... on the left side of my dash... it powers up with the on switch is turned on... need another to even it up.. make it purfect..!

Why do you even need the dash at all?

[Moooools]

Anybody got an FXR kickstart lever to sell me?

[ajturbo]

Anybody got an FXR kickstart lever to sell me?


HTFU and just push start the bitch....:bleh:

[Moooools]

It is for my dad. He is getting pretty old.

[Henk]

It is for my dad. He is getting pretty old.

In that case put the electric start back on :)

[Moooools]

Not that old.

[Dutchee]

Oi cheeky bugga ;)

I have no technique at kick starting 4 strokes, and even have trouble with the odd (very) 2 stroke (GG Pampera, see, very odd). I love my e start on the bucket, apart from mornings when she doesn't really want to play.

It's nothing with being "that old" lol
He just needs to get you to push start him, that'll fix it :)

[Clivoris]

I have this 17x2.75 Suzuki rear rim what needs a sprocket carrier and disc. Sorry but I don't even know what it's off. Anyone got sumfing to do the job?

[Henk]

I've got either a GSXR250 or Impulse Spocket carrier that will fit by the looks, wider an an FXR carrier but nothing that can't be fixed with a lathe, no disk or cush drive rubbers to spare though.
Let me know if you want me to ship one down.

[Moooools]

Oi cheeky bugga ;)

I have no technique at kick starting 4 strokes, and even have trouble with the odd (very) 2 stroke (GG Pampera, see, very odd). I love my e start on the bucket, apart from mornings when she doesn't really want to play.

It's nothing with being "that old" lol
He just needs to get you to push start him, that'll fix it :)

Enjoyed this.
We have found one now so we are all good.

[Pumba]

Oi cheeky bugga ;)

I have no technique at kick starting 4 strokes, and even have trouble with the odd (very) 2 stroke (GG Pampera, see, very odd). I love my e start on the bucket, apart from mornings when she doesn't really want to play.

It's nothing with being "that old" lol
He just needs to get you to push start him, that'll fix it :)

Hmm speaking of kicking a FXR I could sell your kick starter that I still have bolted to the side of my bike

[Henk]

Hmm speaking of kicking a FXR I could sell your kick starter that I still have bolted to the side of my bike

Quite like that back at some stage truth be known. No hurry though.

[Arronduke]

Hmm speaking of kicking a FXR I could sell your kick starter that I still have bolted to the side of my bike

Pure style....:gob:

[Dutchee]

Pure style....:gob:
He's all class dahrling, just total clarss.
Pumba, give ya, hmmmmmmm, nada for it - might not kill ya for now :)
It was commented on, to all and sundry, that you had MY kickstarter. As I can't use one (proven last weekend at Hastings), I don't really care, but apparently my mechanic does lol

[Henk]

Anyone got a rear brake caliper for an FXR in the parts bin complete with the mounting plate.
The reason the back brake on Michelle's FXL100 drags would seem to be that one of the pins that the caliper slides on is corroded completely solid. Can't seem to budge it no matter what I try. Going to steal one off one of the other bikes for now but that will have to be replaced eventually.

[cotswold]

If any one has a GP100 or 125 Motor, or bottom end with a good crank and disc valve I am here with some cash.

[Pumba]

Anyone got a rear brake caliper for an FXR in the parts bin complete with the mounting plate.
The reason the back brake on Michelle's FXL100 drags would seem to be that one of the pins that the caliper slides on is corroded completely solid. Can't seem to budge it no matter what I try. Going to steal one off one of the other bikes for now but that will have to be replaced eventually.

I will have one here, but everything in the shed has been packed up and loaded in a trailer already so you will have to wait till some tome after the move when I figure out where everything is again.

[Henk]

Sweet, thanks, no hurry.

[spada]

Hay ya guys not a bucket but everyone on here I'm sure knows their way around an fxr. One of my fork seals has given up and it looks like the other is on it's way. :violin: Anyone rebuilt the fxr forks before and would be willing give me a hand in replacing the oil and fork seals on the forks? :confused:

[Henk]

Yeah can give you a hand with the forks, I have a set to do anyway, will be sometime in the next three weeks though, racing this weekend and tend to be busy during the week, catch me at the track and we can discuss.

[hmurphy]

I have had a few people asking about getting second hand 125gp slicks for their bucket. My old supplier has run out which makes it hard for me to get slicks when I need them later. Anyone have any contacts...? Cheers.

(PM me if you like, much appreciated for the help!)

[ac3_snow]

Any one have a spare back protector they could bring along for me to borrow on saturday? My mate is coming down for a go and I have two of almost everything except a back protector.

[Henk]

I'll bring Craigs along, he won't be using it.

[ac3_snow]

Chur! hows he doing any way?hopefully he comes along on sunday.

[Henk]

Back at work on light duties this week. Will be coming on Sunday for the flaggies training.

[gav]

Looking for a cheap RS125 fairing.

[timg]

Looking for a cheap RS125 fairing. Here you go Gav http://www.trademe.co.nz/motors/motorbikes/motorbikes/other/auction-366352681.htm Once you've taken the fairing off I'll take the other bits off yer hands for no charge. No need to thank me :no:

[Yow Ling]

Anyone got some TZR250 1KT (early model TZR) wheels for sale. Would look great on my bucket

Thanks
mike

[gav]

Anyone got some TZR250 1KT (early model TZR) wheels for sale. Would look great on my bucket

Thanks
mike

Which one? :laugh:

[Yow Ling]

Which one? :laugh:

any of them, but especially the fxr

[Oleg]

Just watched my mate not making it into the turn on 70km/h. a bit depressing.
list of stuff needed for fxr:
- mirrors;
- screen
- clip-ons
- both hand levers
- foot brake plate and lever;
- gear selector ; plate and linkage
fairings?

Please help.....

[Armi]

I need an FXR right foot peg bracket or help to fix the one I've got. It's bent inwards below the crack.

Edit: I'm also after a right mirror.

246669

[Gigglebutton]

I need an FXR right foot peg bracket or help to fix the one I've got. It's bent inwards below the crack.

Edit: I'm also after a right mirror.

246669

I have welded loads of these. PM me if you need it done. Im in Auckland

[hillbillie]

Looking for an exhaust system, mainly the expansion chamber something that would allow this little motor to peek the rpm’s much faster and more responsive than it is going at now!!!
:soon:
Thanks ya’al

[Moooools]

Just take the expansion chamber off. Everyone knows: Less restriction = more horsepower.:woohoo:


You're Welcome.

[F5 Dave]

Sorry don't know of any around, I have designs, but no parts.

[hillbillie]

Sorry don't know of any around, I have designs, but no parts.

Thank you kindly, might need that in near future!!

[Muzzab]

Looking for an exhaust system, mainly the expansion chamber something that would allow this little motor to peek the rpm’s much faster and more responsive than it is going at now!!!
:soon:
Thanks ya’al

Hi,

I have a chamber off a RM80 (I think), I brought it thinking it was off a 125 but it is smaller. it might be suitable for a 50, $25 + freight, PM me if interested,

Cheers
Muzza

[hillbillie]

Hi,

I have a chamber off a RM80 (I think), I brought it thinking it was off a 125 but it is smaller. it might be suitable for a 50, $25 + freight, PM me if interested,

Cheers
Muzza

Still L-plate, can not PM...... Oo-mupets!!!:facepalm:

[Muzzab]

Still L-plate, can not PM...... Oo-mupets!!!:facepalm:

My digital camera is hiding, but have a look here:

http://www.trademe.co.nz/motors/motorbikes/motorbikes/dirt-bikes/auction-406767959.htm

It is very similar to the pipe in the pictures. It is smaller than it looks.

Cheers
Muzza

[Gigglebutton]

Looking for an exhaust system, mainly the expansion chamber something that would allow this little motor to peek the rpm’s much faster and more responsive than it is going at now!!!
:soon:
Thanks ya’al

I have one under the house you can have. No idea how good it will work

[Henk]

I have one under the house you can have. No idea how good it will work

If you bring it along this weekend we can drag it to Wellington in October if that works for all parties concerned.

[Gigglebutton]

If you bring it along this weekend we can drag it to Wellington in October if that works for all parties concerned.

I will try to find it.

[hillbillie]

I will try to find it.

If it gets here I might get some HP out this little pony.......:scooter:

[hillbillie]

Who can help with a set of rims that will fit my MC16 bucket?

[diablo]

im building up my SL100..
definately want to keep the original wheels, so it's all stock (it's a 1970 model)..
i cant physically go any wider either..

are there slicks available in these sizes or am i dreaming?
if they are a no go, what would be the next best for the track?

front - max poss. tyre width 80 (stock is 70 or 2.75) @ 19 inch

rear - max poss. tyre width 90 (stock is 82.5 or 3.25) @ 17 inch

[Henk]

I've got one each SL and XL 100 frames sitting in the shed taking up space, I know the wheels on them aren't the same sizes and can have a look sometime over the weekend if you like.

[diablo]

I've got one each SL and XL 100 frames sitting in the shed taking up space, I know the wheels on them aren't the same sizes and can have a look sometime over the weekend if you like.

yeah the wheels on the XL100's were either 19/17 or 19/16 i think..

i have wheels.. 19 front and 17 rear..

only really after advice on slicks or similar at the widths and rim sizes as above..

cheers!!

[Henk]

Slicks you'll be able to get 17s, any other size the tyres will be 90 years older than god.

[F5 Dave]

Sorry bud, you are not just dreaming but delusional. 19" slicks, ho ho.

Not trying to be mean (it comes naturally) but slicks are only made for race bikes & in the last 20 years that meant 17".

Your rear rim will be 1.6 wide or close & will only suit a skinny tyre. a 90 slick needs ideally a 2.5" rim, but you can get away with a 2.15.

So you have a nice little SL you want to keep stock. Put some Trials tyres on it & spin it around the place keeping it in good order if that's what you want.

Then go buy a bucket & find some decent tyres/wheels to match.

[diablo]

quite alright.. stupid question n all that..

ill manage with some regular treads..


also: on the hunt for another SL100 or CB100 for my mate if anyone knows of any around.. :blink:


heres a pic if anyone interested.. halfway stripped.. might chuck a monkey tank on..

http://i56.tinypic.com/bg9vt4.jpg

and our street CG125..

http://i51.tinypic.com/2rmv705.jpg

[Henk]

I've got those two rolling frames I need to lose, forks on one look like they might be less rusty than yours.

[diablo]

I've got those two rolling frames I need to lose, forks on one look like they might be less rusty than yours.

pm'd :yes:

[Clivoris]

yeah the wheels on the XL100's were either 19/17 or 19/16 i think..

i have wheels.. 19 front and 17 rear..

only really after advice on slicks or similar at the widths and rim sizes as above..

cheers!!

Maate. check out Alex Hockly of Heidenau tyres. I will send you the email addy via PM. He gets in all sorts of odd sized rubber in modern compounds for classic racers. Super sticky tyres.

[Dutchee]

I will try to find it.
If you find it, flick me a PM/email and I'll take the van to work and pick it up from your work. I'm in Otahuhu, so it's not that far away. Forgot to ask you on the weekend about it ;)

[Gigglebutton]

If you find it, flick me a PM/email and I'll take the van to work and pick it up from your work. I'm in Otahuhu, so it's not that far away. Forgot to ask you on the weekend about it ;)

Ok i'll have a look in the morning. Still at work :(:( No rest for the wicked

[SHELRACING]

Not sure if the swing arm is the same. But I have been working on an XR100. I managed to get a FZR 17 inch to fit into the rear with a 115 x 17 Slick. As for the front end I had a nicely setup CB125 twin forks and FZR front wheel. The forks fitted straight into the original tripple clamps. The only issue might be with the stock rear shocks :(.. Should be a good F5 tho (when I get round to finishing it !!)

Steve


im building up my SL100..
definately want to keep the original wheels, so it's all stock (it's a 1970 model)..
i cant physically go any wider either..

are there slicks available in these sizes or am i dreaming?
if they are a no go, what would be the next best for the track?

front - max poss. tyre width 80 (stock is 70 or 2.75) @ 19 inch

rear - max poss. tyre width 90 (stock is 82.5 or 3.25) @ 17 inch

[diablo]

Not sure if the swing arm is the same. But I have been working on an XR100. I managed to get a FZR 17 inch to fit into the rear with a 115 x 17 Slick. As for the front end I had a nicely setup CB125 twin forks and FZR front wheel. The forks fitted straight into the original tripple clamps. The only issue might be with the stock rear shocks :(.. Should be a good F5 tho (when I get round to finishing it !!)
Steve

May be the same, depending on how old yours is..
I'm waiting to hear back re tyres (not slicks).
If I can't get anything decent, I think I may lace up some 17" rims to some hubs I have.. then get the slicks.
Or get some different forks (31mm - I have a list of all the bikes with this size forks)..
Rear shocks - I am putting my old XV250 (Virago) shocks on mine - 40mm lower..

[Gazzza]

Does anyone have an old frame kicking around going cheap... All I need is the steering head (with bearings)and top and bottom yokes... Any sort of frame as long as it's not alloy. Need it for a sidecar. Cheers.

[Gigglebutton]

Does anyone have an old frame kicking around going cheap... All I need is the steering head (with bearings)and top and bottom yokes... Any sort of frame as long as it's not alloy. Need it for a sidecar. Cheers.

I have a GP125 frame. If thats any good to you, I'll cut the head out

[Ivan]

anyone have any xl or xr 125 or 185 or 200 heads cam and ignitors as im converting my old 1 piece xl125 motor to 2 piece head and going to run total loss cdi setup

[Pumba]

Does anyone have an old frame kicking around going cheap... All I need is the steering head (with bearings)and top and bottom yokes... Any sort of frame as long as it's not alloy. Need it for a sidecar. Cheers.

Got a steering head off a GJ72A GSXR250 (yes just a steering head, rest of the frame has gone to scrap) and a set of FXR triple clamps that fit it, should have some old bearings to go with it as well. It yours if you want it.

[Gigglebutton]

Looking for an exhaust system, mainly the expansion chamber something that would allow this little motor to peek the rpm’s much faster and more responsive than it is going at now!!!
:soon:
Thanks ya’al

I have got the pipe at work & Henk will pick up when he picks up his CB head. It was no good on my RG, but it may match your porting better. Good luck with it

[Gazzza]

I have a GP125 frame. If thats any good to you, I'll cut the head out

Hi mate, I might grab the steering head off Pumba save you cutting up your frame thanks for the offer though.

[Moooools]

Anybody have an rg50 motor that they want to sell. Or any other water cooled 50cc 2-stroke for that matter.

Let me know.

[Yow Ling]

Anybody have an rg50 motor that they want to sell. Or any other water cooled 50cc 2-stroke that matter.

Let me know.

I have a RZ50 motor, needs a rod kit and no ignition, PM me if you are interested

[Moooools]

Anybody want to pick up an RS 125 frame for me in Christchurch, pack it up and ship it to me?
Or if anybody is heading up this way soon?
I might even let you touch it.

Cheers
Max

[F5 Dave]

I have an RG50 engine with RS125 mounts for it about to go begging (not my no27 or anything of course).

[koba]

There eyes met from across the room, the both realised immediatly it was a perfect match...:love:

[chrisc]

Anyone out there have a '82 CG125 guage cluster? The square one in KPH.
Cheers

[Gigglebutton]

I have an RG50 engine with RS125 mounts for it about to go begging (not my no27 or anything of course).

Im keen. I want to put an rg in the RS i have for my daughter. so we can race in f5 together

[Gigglebutton]

Anybody want to pick up an RS 125 frame for me in Christchurch, pack it up and ship it to me?
Or if anybody is heading up this way soon?
I might even let you touch it.

Cheers
Max

So you won it. Grrrrrr I hoped i lost to another bucket racer

[Moooools]

Im keen. I want to put an rg in the RS i have for my daughter. so we can race in f5 together

Get off. :innocent:

[Moooools]

So you won it. Grrrrrr I hoped i lost to another bucket racer

I just about let you have it. Then put one more on for good measure.

[Dutchee]

Im keen. I want to put an rg in the RS i have for my daughter. so we can race in f5 together
If GB gets it, he's got a courier coming down next week to pick it up (who also happens to have to pick up stuff from GB the following week lol).

So you boys fight it out nicely, we've got something to pick up from F5Dave anyway for someone, as well as try to get him in trouble again (nothing to do with us last time, we'd gone to bed).

[F5 Dave]

Max called me so he has the RG engine.

[koba]

So you won it. Grrrrrr I hoped i lost to another bucket racer

Haha! I think there were quite a few eyes on that!

[Moooools]

Anybody want to pick up an RS 125 frame for me in Christchurch, pack it up and ship it to me?
Or if anybody is heading up this way soon?
I might even let you touch it.

Cheers
Max

Anybody? The seller doesn't want to ship it himself.

[Kickaha]

Anybody? The seller doesn't want to ship it himself.

Yeah I can probably do it, flick me the details

[Buckets4Me]

Haha! I think there were quite a few eyes on that!


should have looked at this thread earlier as I have one just like it in the shed
and that rg50 of Daves would have gone nicely in it :facepalm:
that way I wouldn't have had to steal my bike back of young rob (or finish his one:shutup:)

[Dutchee]

should have looked at this thread earlier as I have one just like it in the shed
and that rg50 of Daves would have gone nicely in it :facepalm:
that way I wouldn't have had to steal my bike back of young rob (or finish his one:shutup:)
Are you coming back to racing then? If you're seriously going to take young Rob's bike off him before you finish his, please let us know. I'm enjoying racing F5, but I love watching the kids progressing and gaining confidence. I'm sure we can work around things so that he doesn't have to stop racing. After last meet, he really needs to gain his confidence back.

[Moooools]

Yeah I can probably do it, flick me the details

pm sent +10 Char

[Buckets4Me]

If you're seriously going to take young Rob's bike off him before you finish his.


he would murder me in my sleep

KIDS these days :facepalm:

[Henk]

After a linkage gear setup that will onto a 1970something XL100 so that I can run the rest of the standard FXR pegs etc. Last one I used was off a GPZ600 but now need a second one if someone has someing lurking in the shed. Don't care too much about the spline pattern as long as the bit that goes onto the box is made of a sufficiently cheese like material that it doesn't wreck the splines.

[Ivan]

wanted rear shock something without a side resevioiur myne will hit the swing arm if it has a rear gas res it would be ok or something out of a 250 etc can trade for my one its a chinese fully adjustable shock

[Gazzza]

Wanted an axle, can be either 15 or 17mm dia, the important thing is I need one at least 300 to 350mm long... any one have anything kicking around? Just about ready to start working on the bottom frame of the rig but will need an axle to get some measurements worked out. Cheers, B.

[Harris Ang]

Hello KB i'm looking for ZXR250 Front mudguard would be pretty swole if anyone has one! :v

[Sy]

After a 1998 or similar XR400 headlight unit. Not too fussed about the condition. Cheers

[F5 Dave]

I'm after a left side starter engine for a 1964 Cessner high wing 2 seater.

Or am I posting in the wrong thread?? :facepalm:

[Buddha#81]

I'm after a left side starter engine for a 1964 Cessner high wing 2 seater.

Or am I posting in the wrong thread?? :facepalm:

Were you beaten as a child Dave? Poor guy will be scared for life after your outburst.......that is if he understands what you said?:blink:

[F5 Dave]

well c'mon. . . ZXR250 parts, that's a stretch because maybe some are used in buckets. But XR400 headlights? How bucket is that?

And I hate being beaten. I didn't win a race all weekend so yeah watch out [Smack talk for the BOB starts here]. . .

[Sy]

Sorry, my bad

[Sy]

But XR400 headlights? How bucket is that?

Sorry, my bad, its not for a bucket. I have been trying to find one for a while and just put up a post on the off chance someone might have one.

[F5 Dave]

Try in online trading section, then you might not have grumpy old men like me trying to be funny at your expense.

[Shorty_925]

After a front fairing carrier/frame for an FXR.

[gav]

LMAO, jeez Dave, actually I thought Buddha mightve had something, seeing as he has an XR650. Probably quite a few on here have the odd trail bike crap kicking around the garage ....

[hillbillie]

Hi all,

I just got me a sweet little gp125 motor but I'm in need of a good chassis.
MC19 or MC19 would do me but what ever is out there that will work nicely?:soon:

[Yow Ling]

Hi all,

I just got me a sweet little gp125 motor but I'm in need of a good chassis.
MC19 or MC19 would do me but what ever is out there that will work nicely?:soon:

Would this do? Kinda similar to an fxr
http://www.trademe.co.nz/Browse/Listing.aspx?id=413927313

Pm me if you interested

[Rick 52]

GT 125 ??
http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/other/auction-415619293.htm

[Rick 52]

http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/other/auction-414822843.htm

[Rick 52]

Gp125
http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/complete-engines/auction-415545196.htm

[Kickaha]

28mm Flatslide http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/performance/auction-414911081.htm

[Moooools]

Don't suppose anyone has a set of honda RS125 forks around (pre 95)? Or a shock?
Let me know.

[Yow Ling]

Don't suppose anyone has a set of honda RS125 forks around (pre 95)? Or a shock?
Let me know.

Yea right ! want some wheels as well?

[Moooools]

Yes please. I have a budget of $99.99 and would like them to be sub 1kg.:love:

Yes I know it is a long shot. But someone did offer their services of importing. All is not lost. Please keep your sarcasm off of this family friendly site. :innocent:

[all4A50s]

Don't suppose anyone has a set of honda RS125 forks around (pre 95)? Or a shock?
Let me know.

Ask Andrew Adlam he has whole bike he doesn't ride. Apart from winning every fracken time he rides it.

[Pumba]

Dave Diprose is selling a set on trade me at the moment. Pre 95 model if I recall correct. Current bid was $490 last time I looked

[Moooools]

Yeah that current bid would be me. Just the forks I am after now.

[F5 Dave]

yeah I saw those last night. Flash git that he has enough wide wheels & wets etc that he can sell off the magnesium older ones. I'd buy them in a flash if I had the coin.

& he didn't offer them to me first! I'll hassle him about that.

[Kendog]

Yeah that current bid would be me. Just the forks I am after now.
I liked the look of those wheels, wonder how much I need to bid to win the auction :shifty:

[kel]

I liked the look of those wheels, wonder how much I need to bid to win the auction :shifty:

$1 more than me!

[Moooools]

Let's all just be nice and fuck off. :innocent:
They have scratches all over them and magnesium oxidizes in air to form MgO.
They are probably rotten all the way through.

Get away from my wheels

[Clivoris]

Let's all just be nice and fuck off. :innocent:
They have scratches all over them and magnesium oxidizes in air to form MgO.
They are probably rotten all the way through.

Get away from my wheels

They just bolt straight in to a CBR150r don't they? Will they make me fast enough for A-grade? Be good value for money that.

[chrisc]

Someone help me out here, looking for CG125 parts. Specifically a gauge cluster!
Yodel at me

[Yow Ling]

Couple of mikuni TM28 flatslides

one is RG250 kind $50

one is rg400/500 skinny one for disk valve motors $80
248976
248977
248978

[bartshumandad]

Has anyone got a spare set of useful road legal tyres for an FXR to part with? Need them for a track day . . .

Cheers
Steve

[bozz]

Hi new here.

Just wanted to see if anyone out there has an RGV150 LH footrest bracket.
Oh and L +R peg too, if that's not pushing the boat out :)

Cheers!
Elwin

[Muzzab]

Couple of mikuni TM28 flatslides

one is RG250 kind $50

one is rg400/500 skinny one for disk valve motors $80
248976
248977
248978


Ya reckon one of these would fit the RX100?

[Rick 52]

Has anyone got a spare set of useful road legal tyres for an FXR to part with? Need them for a track day . . .

Cheers
Steve

Yes I have a set !!And a brand new rear ..IRC I think ..What are you offering $$$

[Captian soup]

i have a couple too.

[bartshumandad]

i have a couple too.

Thanks guys, I got sorted already.

[Farmaken]

Hi I am looking for a front disc to fit a GSXR 250 wheel.

Any one got a spare they don`t need ??

Decided I need a set of wets set up after the GP !

[sidwyz]

Just after a rear spring from a fxr or similar?

Busted shock would do the trick, this is not for a fxr so any thing similar may work?

[ac3_snow]

Have Talked my Dad into racing this weekend (was a combined effort, took a bit of persuasion). Is there any one out there with a spare back protector and some boots, size US 12 or mayb 11 (around euro 44-46ish), which my dad could utilise for the weekend would be super choice!.

Cheers.

[Henk]

Can do the back protector, have a pair of shit old boots that may fit but no guarantees. Captian soup hasn't got a spare pair?

[Gigglebutton]

Have Talked my Dad into racing this weekend (was a combined effort, took a bit of persuasion). Is there any one out there with a spare back protector and some boots, size US 12 or mayb 11 (around euro 44-46ish), which my dad could utilise for the weekend would be super choice!.

Cheers.

I wear size 11 and have a pair of boots a bit small for me that he may squeze into

[quallman1234]

After a FXR rear shock or similar

[Henk]

After a FXR rear shock or similar

If you find something. Let me know what works.

[quallman1234]

If you find something. Let me know what works.

Basically just after anything with a decent weight spring, so i can go straight on to the swingarm, instead using a linkage setup. This is for my RS50 frame.

[F5 Dave]

That will require a quiet stiff spring for say 100mm of wheel travel. (I did it on my old RG) Start looking at a 250 shock perhaps.

[quallman1234]

That will require a quiet stiff spring for say 100mm of wheel travel. (I did it on my old RG) Start looking at a 250 shock perhaps.


Cheers dave, thats what i was after.

[Bert]

Cheers dave, thats what i was after.

How long? I've got a few.

[richban]

Basically just after anything with a decent weight spring, so i can go straight on to the swingarm, instead using a linkage setup. This is for my RS50 frame.

I have a GSXR 600 shock I am going to put on trademe some time soon. Yours for 130. Come and get it.

[chrisc]

Asking here for a friend.

He's looking for a suitable 125 2 stroke engine for his FZR framed bucket to be. So GP125, TF etc, any suggestions or have something hanging out that may be of interest please contact me. Preferably in Auckland but may travel for something worthwhile. Muchas gracias

[koba]

Asking here for a friend.

He's looking for a suitable 125 2 stroke engine for his FZR framed bucket to be. So GP125, TF etc, any suggestions or have something hanging out that may be of interest please contact me. Preferably in Auckland but may travel for something worthwhile. Muchas gracias

Seen this?

http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/complete-engines/auction-425063632.htm

That crank looks pretty rusty. You are pretty much up for new bearings in any old shitter though, if you want it to last more than a few races.

[kel]

Does anyone have an older style (90's) Honda RS125 seat unit they would be willing to sell? Any condition considered, Cheers.

[Clivoris]

I'm after an exhaust end can that I can modify onto my DBS exhaust which is currently a little loud.

[F5 Dave]

Just drive it up to Damon (formerly known as Cycleworks, he'll sort it out ok. call him first.
04 526 2345
2019 Akatarawa Road,

[Clivoris]

Just drive it up to Damon (formerly known as Cycleworks, he'll sort it out ok. call him first.
04 526 2345
2019 Akatarawa Road,

Cheers Dave. I'm sure he'd do a great job but I'm thinking a little more budget than that. What I have in mind is something a bit munted that I could cut down as a temporary measure until I can sort something a bit prettier. Or an easy way to quieten down the can/cone I already have.

[Drew]

Seen this?

http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/complete-engines/auction-425063632.htm

That crank looks pretty rusty. You are pretty much up for new bearings in any old shitter though, if you want it to last more than a few races.


I hope he didn't take the picture of the slug as he assembled it. He's got it the wrong way around!

[koba]

I hope he didn't take the picture of the slug as he assembled it. He's got it the wrong way around!

:facepalm::facepalm::facepalm:

Good spotting!

[SHELRACING]

Does anyone have a pair of Honda 125 twin header pipes they wish to part with.

Also looking for a good seat and tail unit. Something like the RS125 ones.

[Ivan]

anyone got any swing arms? mono shock ones

[Moooools]

Ahh yeah just got one off of a Hayabusa. Set up for a 360 section read tyre.
It is a monoshock so should fit right in.

$5 and it's yours.

[F5 Dave]

:laugh:love your work max

[Racey Rider]

anyone got any swing arms? mono shock ones

I've got a couple of spare KR150 ones.

Could do a full, frame / shock / swing arm / rear 18" wheel / disk / and complete rear brake system if anyone needed such.


Heidenau do great 18" race compound rubber, so that's no issue.


Also.... while I'm, here.... :shifty: ... RideLife has 2.75- 16" Heidenau race rubber in stock for those still running the smaller hoops.

Cheers.
Racey.

[Muzzab]

Probably a long shot, but does any one out there have an exhaust or even just a header pipe for a FXR surplus to requirements.
Failing that, any suggestions on any other suitable donor pipes?

Cheers
Muzza

[koba]

Probably a long shot, but does any one out there have an exhaust or even just a header pipe for a FXR surplus to requirements.
Failing that, any suggestions on any other suitable donor pipes?

Cheers
Muzza

I've used a VFR 400 header on one. The diameter was ballpark OK (larger) and the bends are in the right place. I had to slot the holes in the flange to suit the wider FXR holes.

May be a suitable pipe to build from if you happen to have one lying on the floor like I did.

[Muzzab]

I've used a VFR 400 header on one. The diameter was ballpark OK (larger) and the bends are in the right place. I had to slot the holes in the flange to suit the wider FXR holes.

May be a suitable pipe to build from if you happen to have one lying on the floor like I did.

Thanks, heading over to CHCH to check out some wreckers probably best bet.

[motorbyclist]

wanted: FXR/CBR/VTR front mudguard and/or front brakes (caliper-line-cylinder/lever)

[Ivan]

anyone got a honda 125 ignition setup for cdi like stator flywheel and cdi?? my current bottom end is points and top end cdi and was hoping to convert it without going total loss

[motorbyclist]

anyone got a honda 125 ignition setup for cdi like stator flywheel and cdi?? my current bottom end is points and top end cdi and was hoping to convert it without going total loss

two or four stroke? (does it matter?)

I've got some XL125 bits in the shed that might suit...

[Ivan]

sorry should have said it is an xl125 its the old single piece head model, ive since converted the tope end to 2 piece xr200 head with a cdi setup but the bottom end is points

[Ivan]

also thats a good question and i was wondering does it mator if the cdi stator is out of a 4 stroke or not?? like can a 4 stroke run a rm80 ignition with a 4 stroke cdi and coil?

[motorbyclist]

also thats a good question and i was wondering does it mator if the cdi stator is out of a 4 stroke or not?? like can a 4 stroke run a rm80 ignition with a 4 stroke cdi and coil?

I dont see why not....

anyways, I've got a stator coil in unknown condition - XL125 1980-85ish looks like this one but with unpainted motor (http://www.motorcycle-usa.com/photogallerys/Honda-XL-125-12.jpg)

[Ivan]

I dont see why not....

anyways, I've got a stator coil in unknown condition - XL125 1980-85ish looks like this one but with unpainted motor (http://www.motorcycle-usa.com/photogallerys/Honda-XL-125-12.jpg)

is that just the stator or do you have the flywheel as well?

[motorbyclist]

doubtful for the flywheel - I'm 95% sure I've still got the coil attached to cover somewhere in the shed but can't promise much else

[Henk]

After a stock FXR header, just need the first stage skinny bit to make a pipe for a 100. I know I of all people should have FXR stuff coming out my ears but I've pretty much butchered all the ones I had for other bikes.

[kel]

Looking for an FXR carb mount, just the rubber part. The cut down radiator hose isnt working for me. Cheers.

[gav24]

I have a pair of gsx250 rims, 17 x 2.5 front and 17 x 3.5 rear. (with discs, sprocket, cush drive assy, and tyres (100 and 130)
Looking to swap for a pair of 17 inch RGV rims, or just the rear for a rear RGV rim. Looking for a 4, 4.25 or even 4.5 rear rim with the narrower suzuki rear hub, Late RGV ones I know fit but maybe you know that others do to GS500 maybe? 155mm from disc to sprocket, not the bigger ones that are 185 wide hubs.
Or any other decent motard rims for my DR650....What you got!

[Ivan]

I have a pair of gsx250 rims, 17 x 2.5 front and 17 x 3.5 rear. (with discs, sprocket, cush drive assy, and tyres (100 and 130)
Looking to swap for a pair of 17 inch RGV rims, or just the rear for a rear RGV rim. Looking for a 4, 4.25 or even 4.5 rear rim with the narrower suzuki rear hub, Late RGV ones I know fit but maybe you know that others do to GS500 maybe? 155mm from disc to sprocket, not the bigger ones that are 185 wide hubs.
Or any other decent motard rims for my DR650....What you got!

sent a message about my zzr rims

[Bren_chch]

hey

fxr150 speedo sensor... does anyone have one for sale??

cheers

[Henk]

hey

fxr150 speedo sensor... does anyone have one for sale??

cheers

Might have, ask me next week when I've recovered from the weekend.

[Ivan]

anyone got a points coil with capicitor for a early honda single? trying to stay clear of total loss for now

[Moooools]

Anybody got a set of 125 gp slicks that are beyond usable?
Just need something to roll my 50cc project on.
Need to get this thing ready for nationals.

[Pumba]

Anybody got a set of 125 gp slicks that are beyond usable?
Just need something to roll my 50cc project on.
Need to get this thing ready for nationals.

No slicks but I do have a set of rooted tyres here that you can have for said purpose. The only catch is that they are still attached to a set of GSXR rims that you would need to remove them from.

[Pumba]

hey

fxr150 speedo sensor... does anyone have one for sale??

cheers

Did Henk sort you out Bren? I have been cleaning the shed and just came across one if you still need it.

[Henk]

Did Henk sort you out Bren? I have been cleaning the shed and just came across one if you still need it.

No I didn't sort of got a bit side tracked for some unknown reason.
Pumba, yours is probably the better bet since you know where it is, then if that's a fail I can try and drag one out.

[koba]

I need the bit of wiring that goes from the headlights in an FXR. The bit that the bulbs contact.

[Henk]

What the bulb holder thing? Or the whole sodding headlight?
When do you need it by?

[koba]

What the bulb holder thing? Or the whole sodding headlight?
When do you need it by?

The wires and thingamies that plug into the back of the headlight. No big hurry as I've repaired where it has fucked out but my repair isn't the best.

[Henk]

If this

http://www.flickr.com/photos/hz13/6677677221/in/photostream

Is the bit you are after let me know. This one looks a bit fucked but I should have one or three others about. Let me know when you need it.

[koba]

If this

http://www.flickr.com/photos/hz13/6677677221/in/photostream

Is the bit you are after let me know. This one looks a bit fucked but I should have one or three others about. Let me know when you need it.

Yeah, That's the fucker. I'll let you know, there is still a small hope we make another T-town. It was a real pain when one of the wires came off and arced on the earth part. Left me stuck.

[Henk]

Let us know if you are making it to top town, or need one earlier. This one looks like the lead buttons that contact one of the bulbs are a bit worn but can ship it in a hurry if required.

[Ivan]

anyone??? points coils must be lying in someones shed

[SHELRACING]

anyone??? points coils must be lying in someones shed

You can use a the old cylinder coils used on the old car ignitions condensers too. That's what I have used on Wobblers new f5, although it is a total loss system it works good.

[SHELRACING]

I need the bit of wiring that goes from the headlights in an FXR. The bit that the bulbs contact.

I might have one of those, I'll have a look for you tonight and let you know.