Bucket bits 4 sale

[timg]

I grabbed the dr250 carb for my FXR, im planning on buying the copy off metioned website for Cg 125.( building 2 buckets at same time)
Dr250 carb 34mm will this do for my FXR? I was told it the same as a gn250 so im thinking it just needs slightly enlarged hole drilled in bottom of slide like iv read on another post am I correct? I think you'll find 34mm is too large on the FXR. IIRC the GN250 carb is 30mm? A 28mm PWK/OKO works well on a std engine with exhaust mods and 30mm for a full monty worked worked engine. Cheers.

[husaberg]

Yes it is, sorry I was thinking flange mount instead of spigot

They also come as a 33mm (I think it is)

I'd forgotten just how fucking awesome my GN was until you put that pic up, I must drag it out of the shed and fire it up

Start the fire with the petrol tank Peter Fonda.

[Kickaha]

Start the fire with the petrol tank Peter Fonda.

Buy me a TF125 tank and send it over then

[husaberg]

Buy me a TF125 tank and send it over then

Pretty sure the old Man has an X7 tank.
Drive out to a dairy farm and there will be one or two there anyway.
315527

I think one of those skyteam ace ones would look good too.
315528
Measurements are here
https://www.ooracing.com/store/tank-cafe-racer-suitable-for-ace-50-125.html

[Rick 52]

FXR for sale, body work removed, rough around the edges, engine runs very well, big carb fitted
$1000 pic up Waiwera

[Buttman18]

FXR for sale, body work removed, rough around the edges, engine runs very well, big carb fitted
$1000 pic up Waiwera
im keen for a new bucket have you got pics?

[Rick 52]

im keen for a new bucket have you got pics?

Runs great, front tyre is a BT39 Conti on the rear.

[Gixxer88]

Right, xr200 carb sorted for my cg125 where to start with jetting? And have a gn250 carb for my fxr and again not sure on jetting iv never done it

[Buttman18]

Runs great, front tyre is a BT39 Conti on the rear.

Do you any spares wheels, forks or sprockets etc...

[F5 Dave]

Right, xr200 carb sorted for my cg125 where to start with jetting? And have a gn250 carb for my fxr and again not sure on jetting iv never done it
There is no answer for that question.

Search the web for jetting articles (for non CV carbs).

A 172 on main, NDJK needle and 35 on pilot.




. . . will not be right. Really.

[Yow Ling]

Right, xr200 carb sorted for my cg125 where to start with jetting? And have a gn250 carb for my fxr and again not sure on jetting iv never done it

I think a 125 main will work on the gn carb for a fxr

[Henk]

Do you any spares wheels, forks or sprockets etc...

Pretty sure this is just the bike.
Wheels you will want
Forks rarely get bent
Run 12/47 or 12/49 for mount Wellington and you won't need any spare sprockets.

You will want to track down a second set of wheels for wets at some stage no matter what you buy.

[Buttman18]

Pretty sure this is just the bike.
Wheels you will want
Forks rarely get bent
Run 12/47 or 12/49 for mount Wellington and you won't need any spare sprockets.

You will want to track down a second set of wheels for wets at some stage no matter what you buy.

thanks henk

wanted a spare FXR front to put on my RG50

[Gixxer88]

Thanks Yow Ling a place to start and an explanation on why I . . .will not be right F5 Dave?

[F5 Dave]

Gun carb on fxr pretty common, so on std engine should be close. Move from there and it won't be. CG, well who knows? My guess wasn't a guess. Trial and error.

[husaberg]

Gun carb on fxr pretty common, so on std engine should be close. Move from there and it won't be. CG, well who knows? My guess wasn't a guess. Trial and error.

The XR200 carb run open or with a foam filter on the CG125 will be reasonably close. You will likely find your needle and slide out of your original carb will also fit.
As Dave said it will be suck it and see.

[Henk]

Gun carb on fxr pretty common, so on std engine should be close. Move from there and it won't be. CG, well who knows? My guess wasn't a guess. Trial and error.

GN carb on a standard FXR you can leave the jets as they come. Main is a 130 from memory.

[F5 Dave]

Rereading my post I just want to be clear ; don't try a 175 thinking I've suggested it.

[Gixxer88]

Sweet cheers guys I gotta learn this shit sometime I suppose

[Gixxer88]

Also after front fxr axle, I broke the tap while tapping 6mm for nylon bungs or alternative mounting?

[Henk]

Smash it out and go to M8, I've bent or broken more than one M6 cap screw, M8 would be better.

[Rick 52]

http://www.trademe.co.nz/Browse/Listing.aspx?id=950895296

[TZ350]

315923

Kawa 100 fit one of those ""Legal"" :killingme aftermarket AM6 or whatever cylinders and have a fire breathing race machine.

http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/complete-engines/auction-948848431.htm

[TZ350]

315935

TF100 perfect for those cheap 52mm KT100 kart pistons and you could go to a little extra effort and water cool it to and have a top notch motor.

http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/complete-engines/auction-950738299.htm

[TZ350]

316408

$200 buy now.

http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/complete-engines/auction-961567807.htm

[Bert]

316408

$200 buy now.

http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/complete-engines/auction-961567807.htm

Man that was quick Mr Smith

[Pumba]

Man that when quick Mr Smith

have you been talking to my wife? Cause she says that all the time

[Henk]

Please tell me this is for the mk2 sidecar.

[Pumba]

Cheap GSXR250 Rims

Complete front end (just bolt up to your FXR) http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/wheels/auction-961291601.htm

Rear Rim http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/wheels/auction-961296051.htm

[richban]

62mm Standard FXR cylinder for sale $150

FCR33 Carb side draft. Has brand new needle and needle jet. $250 CARB SOLD.....

PM Me if yah want stuff.



316624316625316626316627

[husaberg]

62mm Standard FXR cylinder for sale $150

FCR33 Carb side draft. Has brand new needle and needle jet. $250

PM Me if yah want stuff.





Paging Scott

piity the rider is blunt lol:weep:

[Askor]

Not mine http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/engine-components/auction-968381008.htm

[Henk]

Rear sets that aren't made of cheese

http://www.trademe.co.nz/Browse/Listing.aspx?id=970681083

[cotswold]

http://www.trademe.co.nz/Browse/Listing.aspx?id=967289315

My friend Kimmy has decided to quit as breaking her collar bone and needing surgery to fix it is not on her repeat list, I've ridden this and it's quick.
Bargain for some lucky bugger

[Yow Ling]

http://www.trademe.co.nz/Browse/Listing.aspx?id=967289315

My friend Kimmy has decided to quit as breaking her collar bone and needing surgery to fix it is not on her repeat list, I've ridden this and it's quick.
Bargain for some lucky bugger

Yes it is a good buy, I would get it but have too many, was Timg's he sold it in a fit of insanity

[chrisc]

Hey lads

Is anyone interested in some RS125 fairings I got with my bike? Pictures attached.
They're the slightly larger Pedrosa style fairing meaning they're easier to get behind than the factory ones which even I have a hard time getting behind. Being slightly bigger I could imagine they'd be good to use for a bucket.

After cold seizing my 125 into turn one at Hampton I need some funds to pay for the damage. After $275 for them which I think is pretty fair considering new fairings cost $600+ excl. screen.
I'm on the North Shore in Auckland and work in Mt Wellington so can drop off around there if needed.

I also have the seat which I might sell if someone was particularly interested in it. JHA style.

317025317026

[Rick 52]

http://www.trademe.co.nz/Browse/Listing.aspx?id=978886771&ed=true

[gav]

http://www.trademe.co.nz/Browse/Listing.aspx?id=977534793

317168


SOLD SOLD SOLD

[quallman1234]

Will be selling some stuff soon..

PM If your interested in any of the following...

FXR150 Roller - pretty good condition. Comes with stock wheels and whatever i can find.
YSS Rear shock for a FXR. Its 20mm longer. So we made a new shock mount.
Offers on a TZR250 with a TF125 in it. Not complete. But everything there.

Wellington

[Drew]

Offers on a TZR250 with a TF125 in it. Not complete. But everything there.

Is that the one you got from Jimmy?

[Yow Ling]

https://www.facebook.com/groups/316104995150249/permalink/897859360308140/

[frogfeaturesFZR]

For sale, complete minus lights, and battery. Spent last 4 months stored in my in laws barn. PM me for pics and info. Pirelli Sport Demon tyres, custom paint.

[Askor]

For sale, complete minus lights, and battery. Spent last 4 months stored in my in laws barn. PM me for pics and info. Pirelli Sport Demon tyres, custom paint.

Does it come upside down?

[frogfeaturesFZR]

Does it come upside down?

That can be arranged !
If you click on the image, it comes up the right way
No idea why

[quallman1234]

Is that the one you got from Jimmy?

I have never got anything off jimmy ;). Its a different one.

[TZ350]

317762317763317764

Kitset Bucket Racer:- http://www.trademe.co.nz/motors/motorbikes/motorbikes/other/auction-990356747.htm

[F5 Dave]

So how was he intending to get the Capacity to legal with those cranks?

[Drew]

So how was he intending to get the Capacity to legal with those cranks?

By buying more motors to pull apart and photograph.

[husaberg]

So how was he intending to get the Capacity to legal with those cranks?

Small bore and long stroke.
56.5mmx 57.8mm =144.9cc
57.5mmX 57.8mm = 150.09cc
A few used to run them like that in Aussie, I guess it gave a high compression ratio with a clean piston shape for good combustion speed.

I wondered how an Aprilia RS250 engine cradle makes it easier to fit the Honda engine into the Suzook?
The XR200 bottom ends also have a closer ratio box as it has a higher first gear than the XL125S. (not sure how they compare with the GL145 ratios) but the Gl145 has the largest valves +1mm compared to the 125s/185/200 but needs to be converted from points) from memory the GL145 also has a roller bearing end on the crank. (but its been years)
The later cranks can be swapped easily but the early ones have different bearing sizes.
I have seen a guy put a XR200 barrel and crank onto a CB100 as they have a better set of ratios in a 5 speed.
but that involves welding up the oil gallery into the crankcase mouth that gets bored into to fir the spigot. and turning down one or maybe two of the cranks bearing surfaces.

[RMS eng]

for sale my 1989 Suzuki RGV250 VJ21,was going when I got it ,but was going to make a pre 89 race bike,so I have stripped the motor down,the LH main bearing was done ,rest of motor look good.$1600.00 or best offer phone chris 09 817 9500

[sidecar bob]

I discovered this bucket on the porch at a party last night. I wonder if anyone knows its back story. Seems very well built & has had a lot of effort put into it.
It hasn't been ridden for several years, but appears to need nothing more than everything servicing to be a runner again.
It has a very nicely put together 125 twin out to 140, with an alloy spacer under the barrel.
What would it be worth?

[husaberg]

I discovered this bucket on the porch at a party last night. I wonder if anyone knows its back story. Seems very well built & has had a lot of effort put into it.
It hasn't been ridden for several years, but appears to need nothing more than everything servicing to be a runner again.
It has a very nicely put together 125 twin out to 140, with an alloy spacer under the barrel.
What would it be worth?

A couple of dozen beers
No ide on the history but someone will
It looks to have a set of Suzuki wheels
From hearing what the north Islanders say Most of the fast Honda twins trace their linage to Mr O'Connor.


PS remember how nodrog wanted a free superbike to race:msn-wink:

[Pumba]

I discovered this bucket on the porch at a party last night. I wonder if anyone knows its back story. Seems very well built & has had a lot of effort put into it.
It hasn't been ridden for several years, but appears to need nothing more than everything servicing to be a runner again.
It has a very nicely put together 125 twin out to 140, with an alloy spacer under the barrel.
What would it be worth?

Looks very well done, braced swing arm, GSXR rim on the back (well Calliper at least). Front wheel looks more FZR with the singe large floating disc.

Would be a good B grade bike, and with the right rider could upset a few in A grade no doubt.

I would expect it to be somewhere just under the $1000 mark.


From hearing what the north Islanders say Most of the fast Honda twins trace their linage to Mr O'Connor.

Engine internals MAY trace back to him, but all his bikes (well the ones I know) had the two into one under slung muffler set up.

[husaberg]

Looks very well done, braced swing arm, GSXR rim on the back (well Calliper at least). Front wheel looks more FZR with the singe large floating disc.

Would be a good B grade bike, and with the right rider could upset a few in A grade no doubt.

I would expect it to be somewhere just under the $1000 mark.



Engine internals MAY trace back to him, but all his bikes (well the ones I know) had the two into one under slung muffler set up.

Right you are with the yam disk and likely wheel i was thinking one of those GSX250 with the single disk but their disk holes are round.
Spacer plate i guess for different pistons not sure what the big bores used at all.

[jasonu]

Looks very well done, braced swing arm, GSXR rim on the back (well Calliper at least). Front wheel looks more FZR with the singe large floating disc.

Would be a good B grade bike, and with the right rider could upset a few in A grade no doubt.

I would expect it to be somewhere just under the $1000 mark.



Engine internals MAY trace back to him, but all his bikes (well the ones I know) had the two into one under slung muffler set up.

A grand for a bike that is heavy and slow. Don't think so... $500 is my guess

[Drew]

CT90 slugs take them to about 144cc if I recall from the maths we did years ago. Dunno why the spacer would be needed.

[Kickaha]

CT90 slugs take them to about 144cc if I recall from the maths we did years ago. Dunno why the spacer would be needed.

Piston pin height might be different

[Grumph]

CT90 slugs take them to about 144cc if I recall from the maths we did years ago. Dunno why the spacer would be needed.


Piston pin height might be different

CT90 deck height is actually lower so no spacer, in fact barrel would need machining...No idea what pistons could be fitted.

[F5 Dave]

Maybe Rich has been in there. XR185 pistons?

[cotswold]

Not sure if you guys have heard but some low life has nicked the Auckland club bike, if you get offered parts can you check where they came from

[sidecar bob]

Not sure if you guys have heard but some low life has nicked the Auckland club bike, if you get offered parts can you check where they came from

Keep an eye on the F1 entries for Cemetery Circuit, Its probably Nodrog. Hes been getting fairly desperate for a supplied ride.

[Hilleye]

CT90 deck height is actually lower so no spacer, in fact barrel would need machining...No idea what pistons could be fitted.

The highest point on the CT90 piston is 1.00mm lower, but the piston edge where the compression dome starts is actually 0.5mm higher according to TKRJ. Spacer might be to stop the outside edge of the piston compression dome contacting the cylinder head at the edge of the combustion chamber. However, I wouldn't have thought that these pistons were an option because it'd give you a total displacement of 161cc.
CT 90: http://www.tkrj.co.jp/goods/m-AH0350X--028-070.php
CB125T http://www.tkrj.co.jp/goods/m-AH0670X--399-010.php

Might be C70 pistons though, which are basically a +3.00mm from the CB125T pistons. These would give you 142cc. Possibly still need the spacer due to the increased width of piston vs cylinder head combustion chamber. These are also probably as big as you can go without changing the original cylinder liners.
C70: http://www.tkrj.co.jp/goods/m-AH0210X--087-712.php

[Grumph]

Disagree...You'd use C90E pistons which have a lower deck height than the CB125T ones - and are 47mm bore.
Once you'd cut the barrel to get correct deck height, you'd machine the piston crowns for squish shape to match the head.
i suspect that the earlier reference to CT90 pistons should have been C90...
BTW the C90 and CB125 both use 13mm pins where the CT90 uses 14mm...

But again, this just points up that the engine in question must use something very different....

[husaberg]

Disagree...You'd use C90E pistons which have a lower deck height than the CB125T ones - and are 47mm bore.
Once you'd cut the barrel to get correct deck height, you'd machine the piston crowns for squish shape to match the head.
i suspect that the earlier reference to CT90 pistons should have been C90...
BTW the C90 and CB125 both use 13mm pins where the CT90 uses 14mm...

But again, this just points up that the engine in question must use something very different....

My moneys on Pit bike pistons.
http://dratv.com/encoon.html
Far greater choice of dome shapes,
he could also have used earlier Honda twin pistons.
http://thumbs1.ebaystatic.com/d/l225/m/mKBcv3GkeJjUlNkTNstdUng.jpg

[sidecar bob]

My moneys on Pit bike pistons.
http://dratv.com/encoon.html
Far greater choice of dome shapes,
he could also have used earlier Honda twin pistons.
http://thumbs1.ebaystatic.com/d/l225/m/mKBcv3GkeJjUlNkTNstdUng.jpg

One of you chums should buy it & pull it to bits & find out. I bet i could get it for you pretty cheap.

[husaberg]

One of you chums should buy it & pull it to bits & find out. I bet i could get it for you pretty cheap.

There is someone on KB wanting a bucket at the moment.

Anyone know of any buckets for sale in auckland?
Not my cup of tea as it has to many springs and valvey things.
Failing that you could always ask the guy who owns it..............
Or buy it for Nodrog and tell him its a superbike.

[Nobbsie]

yea i could be interested if the price is right

[cotswold]

Just putting this out there, a mate in Holland is selling his 50 in parts and has a very nice NX4 front end (no Wheel but brake is there) whats it worth bearing in mind you still have to pay shipping ( although I am buying a few bits and bobs so we could come to a joint arrangement)

[mr bucketracer]

Just putting this out there, a mate in Holland is selling his 50 in parts and has a very nice NX4 front end (no Wheel but brake is there) whats it worth bearing in mind you still have to pay shipping ( although I am buying a few bits and bobs so we could come to a joint arrangement)whats he wanting for it?

[cotswold]

whats he wanting for it?

to honest I have no idea, he just asked me if I would be interested, he has a NSR50 engined bike from the old Dutch series, bike minus wheels, the frame is home built out of bits and bobs but it has that front end NX4 rs125 fork, titanium brembo caliper, honda master cylinder,

You boys would have an idea of worth, I've tried finding some on ebay but nothing found

[cotswold]

to honest I have no idea, he just asked me if I would be interested, he has a NSR50 engined bike from the old Dutch series, bike minus wheels, the frame is home built out of bits and bobs but it has that front end NX4 rs125 fork, titanium brembo caliper, honda master cylinder,

You boys would have an idea of worth, I've tried finding some on ebay but nothing found

.................................................. .................

[kel]

You boys would have an idea of worth, I've tried finding some on ebay but nothing found
About a grand NZ a couple of years back for the non radial brake type. Of course RS parts keep going up and up, plus our dollar has dropped at least 15% against the pound since then.

[mr bucketracer]

we have picked up most of are ones for 400-500 hunderd , if you just willy nily buy some you will pay up around 1000 dollars , clamps are 170-300 but we have are own , ashame to break the bike up by the looks

[koba]

Wheels for Sale:

From an FZR 250, these are lighter than most road rims in the same size.

Rear - 3.5" Has a Disc, no cush drive and is missing 2 of the cush rubbers.
Front - 2.75" - Bare, has a dent in it - I'll let this go for bugger all, a few good hammer hits might bring it back but this is at your own risk.

I'll be selling another front soon, I just need to work out which of the two fits on my bike better, they are slightly different.

Offers.

[TALLIS]

http://www.trademe.co.nz/motors/motorbikes/motorbikes/sports/auction-1036428563.htm
Looks like a good start, I'm sure someone was asking for one up those ways

[koba]

That was amazing!

[Nobbsie]

r15 up for sale on tm
de reg
http://www.trademe.co.nz/motors/motorbikes/motorbikes/sports/auction-1042171477.htm

[Aeromo]

GSX 250 Front Rim. GJ72

Sorry wrong section, should be wanted to buy

[Buttman18]

http://www.trademe.co.nz/Browse/Listing.aspx?id=1045602987&ed=true

[chrisc]

Anyone after a cheap front stand? 320227
$40 in auckland. Pm me

[mr bucketracer]

Anyone after a cheap front stand? 320227
$40 in auckland. Pm meyip will take that:niceone: sick of making things

[husaberg]

H100 manual

http://www.trademe.co.nz/motors/motorbikes/parts-for-sale/manuals-magazines/auction-1043497635.htm

[F5 Dave]

What's a manual for? Only a homo puts an engine back together without at least trying to make it faster. The instructions are merely the manufacturer's opinion of how it should go together.

[husaberg]

What's a manual for? Only a homo puts an engine back together without at least trying to make it faster. The instructions are merely the manufacturer's opinion of how it should go together.

It has the piston clearances, Plus lots of boring belts and braces stuff for those not keen to entirely use up the worlds supply of Rare NOS Yamaha YZ100 pistons.
They also have a rather cool twice as big than A3 line drawing of the bike.

[Bert]

It has the piston clearances, Plus lots of boring belts and braces stuff for those not keen to entirely use up the worlds supply of Rare NOS Yamaha YZ100 pistons.
They also have a rather cool twice as big than A3 line drawing of the bike.

Some of us happen to have half the world supply of YZ100 pistons...

[Henk]

Some of us happen to have half the world supply of YZ100 pistons...

You Dave G MK2?

[husaberg]

Some of us happen to have half the world supply of YZ100 pistons...

So who was using the even rarer RM100 ones?

[Bert]

You Dave G MK2?

Well my shed is full and have taken over Scotts for a little while now.
But I've got another 20 years to catch Dave or even Scotty.


So who was using the even rarer RM100 ones?

Not me, I needed the 16mm pin for the TZR rods.

[mr bucketracer]

So who was using the even rarer RM100 ones?i did have some wisco rm100 ones for the tf100s

[Yow Ling]

i did have some wisco rm100 ones for the tf100s
Got any left?

[goivy26]

TF 125 Race Motor with carb and ignition.

Offers

SOLD

[goivy26]

ER 250 (ZZR) Roller and MB50 set up for TF125 Roller. Rim sizes on the ER are 3.50x17 Rear and 2.50x 17 Front

Offers

SOLD

[quallman1234]

Hey peeps,

Got a FXR framed bucket with a DR125 engine in it. With a 150cc kit. Made 15hp on the dyno..
Slicks and all nylon, ready to go. Great bike for a B grader who wants to get into it, without messing about.

Want a 1000$ for it.

Wellington.

[Buttman18]

have a set of RG50 rims and tires as well as some front forks if anyone wants them

[1fletch1]

Hey peeps,

Got a FXR framed bucket with a DR125 engine in it. With a 150cc kit. Made 15hp on the dyno..
Slicks and all nylon, ready to go. Great bike for a B grader who wants to get into it, without messing about.

Want a 1000$ for it.

Wellington.



Any chance of getting it to Auckland or edgecumbe?

[mr bucketracer]

have a set of RG50 rims and tires as well as some front forks if anyone wants themi would be keen on the forks

[quallman1234]

Hey peeps,

Got a FXR framed bucket with a DR125 engine in it. With a 150cc kit. Made 15hp on the dyno..
Slicks and all nylon, ready to go. Great bike for a B grader who wants to get into it, without messing about.

Want a 1000$ for it.

Wellington.



Any chance of getting it to Auckland or edgecumbe?

Yeah perhaps edgecumbe post photos tomorrow

[quallman1234]

Hey peeps,

Got a FXR framed bucket with a DR125 engine in it. With a 150cc kit. Made 15hp on the dyno..
Slicks and all nylon, ready to go. Great bike for a B grader who wants to get into it, without messing about.

Want a 1000$ for it.

Wellington.



Any chance of getting it to Auckland or edgecumbe?

Also has clip ons, under exhaust and raised pegs. Electric start only. Everything of a fxr works on it. Same gear rod length etc. Right rider should smash b grade

[Buttman18]

i would be keen on the forks

sold pm me mate

[chrisc]

I have 3 XL carbs in various states of usability which I got with a bike recently. I'm sure you'd be able to make one or even 2 good ones from the box of bits. I know Gavin Veltmeyer uses them with great success and Terrene's FXR also uses them well. A good upgrade on the factory pee sized choker carb. No idea what they're worth, hows $50 for the lot pick up Auckland? PM me

[TZ350]

320878

http://www.trademe.co.nz/a.aspx?id=1064601741

Yamaha YZF R15B 149cc

[Rick 52]

TF 125 Race Motor with carb and ignition.

Offers

Im keen on this engine, whats been done, HP ?

[dytekdan]

Hey peeps,

Got a FXR framed bucket with a DR125 engine in it. With a 150cc kit. Made 15hp on the dyno..
Slicks and all nylon, ready to go. Great bike for a B grader who wants to get into it, without messing about.

Want a 1000$ for it.

Wellington.

Is this machine still for sale

[goivy26]

Im keen on this engine, whats been done, HP ?

Sorry Rick it's sold.

Ivan

[Askor]

I'm selling my spare bucket http://www.trademe.co.nz/Browse/Listing.aspx?id=1072516741&ed=true

[quallman1234]

Looking for 17" wheels. as close to 2.5 and 3.5 Wellington

[omamari]

Looking for 17" wheels. as close to 2.5 and 3.5 ... Auckland

[mr bucketracer]

Looking for 17" wheels. as close to 2.5 and 3.5 Wellingtonwhat make ? zxr 250 ?

[Drew]

Anybody want some GT125 motors? Two sets of cases, one motor together that seized on track and another one in bits. Three cranks, two of which need rod kits. Shit loads of bits.

[Aeromo]

Honda Wheels. 2.5" front, 3.5" Rear
Rear includes sprocket, sprocket carrier and disk, bearings.
No disks for front.

$180

[Rick 52]

FXR $1400

http://www.trademe.co.nz/motors/motorbikes/motorbikes/other/auction-1084287432.htm

[quallman1234]

ZXR250C Chassis, GSXR600 Shock, FXR150 Engine (Cams,carb, big piston and pipe). Handles awesome now!
In the region of early 20hp (seen a max of 22hp). Carb is a bit average so i will get a oko if i sell it and jet it in on the dyno.

Want 2,500 for it, or i wont sell it (Moving countries and will just keep here till im back).

Full nylon and everything for Kaitoke or a NI Series round. Ideal for bigger riders as well :).

Preferably keep in wellington.

[muffin]

Anyone out there with a bucket sidecar for sale ?

[ac3_snow]

Anyone out there with a bucket sidecar for sale ?

Yea I have one in the garage, its:
Old,
Kinda slow,
Hard work to drive,
Hard work to swing on,
Great on two wheels,
Heaps of fun to slide around in the wet.

Its an old Yamaha YB100, if your keen I can dig out some pictures.
I won't be at the track this weekend otherwise you could have seen it in person.

[chrisc]

125GP slicks for sale! - Auckland
I have 2 new front slicks for sale, one Dunlop, one Bridgestone. All funds received funnelled straight into my boiling racing addiction. See the two listings below. No buy nows or selling outside of trademe thanks.

Bridgestone: http://www.trademe.co.nz/Browse/Listing.aspx?id=1089946362

Dunlop: http://www.trademe.co.nz/Browse/Listing.aspx?id=1089945186

[richban]

Hi All.

I have 2 brand spanking KTM 200 throttle bodies for sale. $250 each. These are 38mm so perfect for a 150 tuned engine. I will post some pics later. PM if keen.


CHeers

[mr bucketracer]

Hi All.

I have 2 brand spanking KTM 200 throttle bodies for sale. $250 each. These are 38mm so perfect for a 150 tuned engine. I will post some pics later. PM if keen.


CHeersuse them on the nsr (-;

[quallman1234]

FXR150, Wellington
Carb
Pipe
Rearsets
Clipons
Nylon
Slicks
Tailpiece
Ready to race @ Kaitoke
$1600

Its a tidy build! You wont be able to build one this nice for this price!

I've also got some random things

Anyone need zxr250 discs?

[gav]

FXR150, Wellington
Carb
Pipe
Rearsets
Clipons
Nylon
Slicks
Tailpiece
Ready to race @ Kaitoke
$1600

Its a tidy build! You wont be able to build one this nice for this price!

I've also got some random things

Anyone need zxr250 discs?

Got any photos?

[quallman1234]

Got any photos?

PM'd. I will orgainse more :).

321878

[quallman1234]

321879

10 characters

[quallman1234]

Got any photos?

The owner is driving through christchurch next week if your interested in it.

[Pumba]

Anyone got any use for a lightly used FXR head.

http://uploads.tapatalk-cdn.com/20160528/6df1a7fb58b2361f5c89d3b03c7efab0.jpg

Having a clean out so if no one wants it for whatever strange reason I will scrap it.

P.S. I was going to pull the carb flange off and keep in my parts bin


Sent from my iPhone using Tapatalk

[F5 Dave]

In the words of various south islanders;

Gee you're rough on gear:lol:

[Pumba]

Well yea Dave, but on this occasion I am not responsible for the destruction. Just something I inherited. This is the head off the first engine that I am aware of that tried running a Kawasaki piston. Apparently it sounded pretty shit hot for the first 5min.

[timg]

http://www.trademe.co.nz/Browse/Listing.aspx?id=1099956181

[Aeromo]

3.0" GSX Rear Rim Off GJ72
As in photos, rim only. I do have a RG150 sprocket carrier with 47T sprocket and rubbers that can go with it.
$50?

[1fletch1]

3.0" GSX Rear Rim Off GJ72
As in photos, rim only. I do have a RG150 sprocket carrier with 47T sprocket and rubbers that can go with it.
$50?

Whats your number? Im headimg down to edgecumbe this weekend and could be keen to purchase it. Cheers Ryan 02102247005

[Aeromo]

http://www.trademe.co.nz/Browse/Listing.aspx?id=1113226240

[TALLIS]

Apparently impossible to find, so here one is

http://www.trademe.co.nz/motors/motorbikes/motorbikes/sports/auction-1115721131.htm

[cotswold]

Apparently impossible to find, so here one is

http://www.trademe.co.nz/motors/motorbikes/motorbikes/sports/auction-1115721131.htm

And it's only 3 times the price of an fxr

[Grumph]

And it's only 3 times the price of an fxr

Seems fair to me...cough....

The shipping details are interesting. Not sure i'd be happy shipping it interisland on an open pallet.

[Kickaha]

And it's only 3 times the price of an fxr

6 x the price of the FXR I just bought :bleh:

[andrew a]

I find it hard to read an add for a bike like the RS 50 saying only a car licence needed and no WOF.
Most of you know i'm not exactly normal so have a couple of Honda Chaly bikes. I have put one back on the road but what a hassel. It has .5 to much kilowatts to be registered as a moped. I got it through in the end. I purchased another one with the reg on hold and thought great but unfortunately registered as bike needing a WOF and three times more to register. I will try to get it changed but will be a problem. The one I have is so horrible to ride. It is so slow it is incredible. If it needed a WOF it would probably fail because it cant move fast enough to get out of the way!
A moped can only be capable of doing 50kph he is advertising it as being able to do 105kph!

[TALLIS]

I find it hard to read an add for a bike like the RS 50 saying only a car licence needed and no WOF.
Most of you know i'm not exactly normal so have a couple of Honda Chaly bikes. I have put one back on the road but what a hassel. It has .5 to much kilowatts to be registered as a moped. I got it through in the end. I purchased another one with the reg on hold and thought great but unfortunately registered as bike needing a WOF and three times more to register. I will try to get it changed but will be a problem. The one I have is so horrible to ride. It is so slow it is incredible. If it needed a WOF it would probably fail because it cant move fast enough to get out of the way!
A moped can only be capable of doing 50kph he is advertising it as being able to do 105kph!

I have a rg50 which is registered (changed to a moped from motorcycle by default before me because it was a 50 apparently) which dose 95km with me on it, and a Honda dream 50 which registered as a motorcycle by vtnz because it's to quick 65 - 70 on a good day. I understand your pain, as you know common sense has no place in today's rules and regs.

[Pumba]

Of course as a Licensed Motor Vehicle Trader he would be liable under the Fair Trading Act 1986 if false or misleading information is contained in the Customer Information Notice which of course he is legal required to display under the Motor Vehicle Sales Act 2003.

Might to do some fishing on his FB advertisement and see if I can become black listed.

[F5 Dave]

Me and Darrin had some good duels on our road RGs and could indicate 118, or was it 113? Equated to a real 105. Did six cold kiwi rallies on mine despite having an 1100 to go on.

[andrew a]

I have a KTM 125 Duke motor for sale. Has been bored to fit CBR150 piston so it is 150cc. Needs to be assembled. Comes wit piggy back computer for adjustable mixtures and spark.
Call me if interested. 021 030 5874

[Pumba]

Street Triple Muffler.

Its way too big and heavy to put on a bucket but you may have a use for it

323035 323036

[F5 Dave]

Looks too big and heavy for my Street Triple.
Ahh heck pic is on my pH not tablet.

Just done suspension mods today first ride. Soo much better. PM me if interested.

[Henk]

Street Triple Muffler.

Its way too big and heavy to put on a bucket but you may have a use for it

323035 323036

Sorry, I don't own a boat.

[Pumba]

Looks too big and heavy for my Street Triple.
Ahh heck pic is on my pH not tablet.

Just done suspension mods today first ride. Soo much better. PM me if interested.

Still got my Speed Triple. I bought this one apparently, I dont even remember putting the $1 bid on it. Now I dont want it cluttering up the shed.

Presume you have thrown a aftermarket system on there?


Sorry, I don't own a boat.

About all it is good for

[Yow Ling]

TF100 engine , Pete Sales porting, RM125 ignition , TM28 flatslide , 6 speed, engine only $250

323102

PM if interested

[F5 Dave]

Aww cmon! That's the best bike you own.

[Kickaha]

Aww cmon! That's the best bike you own.

It'll be better with a four stroke in it though :bleh:

[Yow Ling]

Aww cmon! That's the best bike you own.

There are some others that I love more

I knew a guy who used to have a flash 50

323136323135
Looks like it will fit

[Kickaha]

Looks like it will fit
Like it was made for it

[F5 Dave]

Nah, an RZ350 was made to fit. Two small plates and you're away.

[Drew]

Nah, an RZ350 was made to fit. Two small plates and you're away.

For the front mount? I've heard tell of such a thing, I couldn't believe it was that easy.

[F5 Dave]

There were mag articles back in the day with drawing. Mines done a little different with frame bracing allowing for the torque arms the RZ uses. Not really required for a std RZ engine in RG.

[Grumph]

For the front mount? I've heard tell of such a thing, I couldn't believe it was that easy.

Guy here came to me with the patterns, wanted me to do them. I showed him the vice and hacksaw,handed him a piece of 8mm plate and told him to get on with it...Drilled the holes for him and linished the outside edge of the plates....15minutes, tops.

Made a set of pipes for the yammagamma though which took rather longer...and cost him a tad more.

[Yow Ling]

TF100 engine , Pete Sales porting, RM125 ignition , TM28 flatslide , 6 speed, engine only $250

323102

PM if interested

sold sold !

[Henk]

Terrene looks to be selling her bike.

http://www.trademe.co.nz/Browse/Listing.aspx?id=1131344116

Turn up and go racing nothing else to do. Just getting wide rims on a bike is going to cost about $500 these days.

[goivy26]

It is with a heavy heart that I put up for sale my nsr250 sp ts125 bucket project.

Pretty much all done just needs assembly and finishing.

Engine mounts all done
Fully worked ts 125 (been running)
RS 125 tail
Decent subframe
3.5 x 17 rear wheel conversion, 5 spoke honda. (Needs finishing)
Fully adjustable suspension front and rear.
3x chambers to work with
Lots of spare motor parts clutch heads etc
Spare lightend and balanced crank with new rod.
Plus heaps more!!!!!

Open to serious offers and will put up some photos as soon as I can.
Genuine reason for sale.

Ivan
0273032564 or pm me

[timg]

Ok. My TZR/FXR superbucket is nearing completion and I need to recharge the coffers and get rid of some stuff. Check it out;

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137280253

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137461195

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137465589

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137498293

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137504681

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137452271

Cheers

[husaberg]

Ok. My TZR/FXR superbucket is nearing completion and I need to recharge to coffers and get rid of some stuff. Check it out;

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137280253 Dellorto PHF32 carbs

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137461195 TZR250 Tank

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137465589 FXR150 Race Cams

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137498293 Suzuki FXR150 Bucket frame

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137504681 Suzuki FXR150 box of spares

http://www.trademe.co.nz/Browse/Listing.aspx?id=1137452271 Suzuki FXR150 2003 race bike GPR tuned engine

Cheers

Tim I Edited to reflect that most on KB have used the dark zone forum skin, and like links that work:msn-wink:
I assume the beer is in the mail.

[timg]

Tim I Edited to reflect that most on KB have used the dark zone forum skin, and like links that work:msn-wink:
I assume the beer is in the mail. Cool. Links worked for me... :) You've got a big shed - you need to buy some more stuff :yes:

[husaberg]

Cool. Links worked for me... :) You've got a big shed - you need to buy some more stuff :yes:

They do now that you have removed the colour.....
Yes, A huge shed used to be a horse trainers stable, bigger than most houses I guess. But ask arround if size matter though. because even though its huge, it takes me ages to finish anything:shutup:
Does all this mean I get no beer?

[timg]

Does all this mean I get no beer? Always a beer for you here any time you're passing mate :drinknsin

[Henk]

http://www.trademe.co.nz/a.aspx?id=1144073572

I'm pretty sure looking at the photos that this is the old road bucket that I built a few years back.
From memory the front axle should be drilled and tapped to take crash bungs, the pipe has been moved under the bike and the engine is basically stock, still had electric start when I sold it.
I thought I had put more solid rear sets on it but they look to have gone elsewhere.

Cheapish buy it and race it option in any case.

[Calvert86]

https://trademe.co.nz/1148150555

Saw this pop up today...may interest someone!


Calvert86

[Henk]

https://trademe.co.nz/1148150555

Saw this pop up today...may interest someone!


Calvert86

I know this bike, not sure how fast it could be punted but it sure is pretty.

[Calvert86]

I know this bike, not sure how fast it could be punted but it sure is pretty.

Yep 10/10 for looks! I need something like this that makes me look fast in the pits!


Calvert86

[husaberg]

I know this bike, not sure how fast it could be punted but it sure is pretty.

That lower fairing sure is neatly done.
324072

[TZ350]

324466

Two for the price of one.

http://www.trademe.co.nz/motors/motorbikes/motorbikes/sports/auction-1157391179.htm

[Autech]

Selling my FXR, in the trading section of KB if anyone's interested. Good price so hopefully should sell fast. Tell a friend :Punk:

324764

[Motolorax]

This one is too far north for me but might be interesting for others: http://www.trademe.co.nz/Browse/Listing.aspx?id=1177030202

[Askor]

GP125 engine http://www.trademe.co.nz/Browse/Listing.aspx?id=1180318502

[k14]

I've got a RS125 subframe with 2001 model tail piece. Been sitting in my garage for about 5 years gathering dust. The tail piece needs a bit of tlc, I've half done it but will need a bit of fiber glassing and bogging to get looking nice again. Subframe is straight.

I'm thinking $100? Shipping could be a bit of a pain but it is light and Fastway charges by weight so might only be $10-20?

[timg]

I've got a RS125 subframe with 2001 model tail piece. Been sitting in my garage for about 5 years gathering dust. The tail piece needs a bit of tlc, I've half done it but will need a bit of fiber glassing and bogging to get looking nice again. Subframe is straight.

I'm thinking $100? Shipping could be a bit of a pain but it is light and Fastway charges by weight so might only be $10-20? Kirk, is it a std subframe or lengthened? Thanx.

[Sketchy_Racer]

I'm selling my rolling chassis that I had the RM85 cheater motor mounted in.

Suzuki RGV VJ21 chassis and SP forks
2.5" front wheel and 3.5" rear wheel for perfect 125GP slick fitment
Bridgestone Slicks front and rear in good nick
Rear sets with gear lever and brakes all sorted
Adjustable clipons

This is pretty much a bolt a motor in and race chassis that is setup to a level that can run at the very front of A-Grade at wellington buckets.

here's a video on board.

https://www.youtube.com/watch?v=k27J_MVrRrk


Looking for $500

[cotswold]

http://www.trademe.co.nz/a.aspx?id=1202570699

looks like a good starting point for a fast 2T

[FastFred]

http://www.trademe.co.nz/a.aspx?id=1202570699

looks like a good starting point for a fast 2T

Looks the Shissss. A decent 2T racer.

326199326200


Honda mc18 nsr 250 bucket racer ,fresh tf125 motorJust run in from a full rebuild ,Including extensive porting polishing and 6spd gear box from a ts125, bike goes extremly well and would be competitive with the right rider,selling due to a knee injury outside the sport, bike will come with a complete bottom end from a ts125 including spare 6 spd gear box , will also come with original tail cone , recent fork rebuild and fresh paint,bike has sliders all round ,soft set of slicks,new clutch also ,in no rush to sell as currently looking for a muscle car project ,2500,firm

[Calvert86]

Ground up rebuild last year with new steering head bearings, chain and sprockets
New oil in front forks
Rewired and stator motor removed so running total loss with new battery installed last year
Hel brake lines front and rear
Oko 28mm carb with see through float bowl
Big knobs bucket bike protection kit so up to kart track standard and just regripped the pegs with 3M grip tape
Raised rear sets
Shortened header pipe fitted to a Ducati s4r muffler which has just been repacked
Wider rims 2.5" front and 3.0" rear running slicks
Also includes standard rims with wets

Everything was stripped and cleaned last year.
Bike did 3 events at the north island series running B grade and hasn't been used since. Selling as not getting used and baby due this month means will miss north island series again!!

Comes with rego on hold, old plastics, lights and exhaust to put back on road and also will throw in front and rear paddock stands

2800 ono...located Wellington
http://uploads.tapatalk-cdn.com/20161124/6986801df832c345fd04d7b88ff73f95.jpg


Sent from my iPhone using Tapatalk

[ac3_snow]

FXR $1600 Wide wheels, underslung exhaust, clip ons and full nylon. Comes with standard wheels (on street tyres, never got around to buying wets) plus 98% of the road gear (passenger footpegs are no longer attached and think its missing a mirror or two) rego on hold.

<a data-flickr-embed="true" href="https://www.flickr.com/photos/sonscc/25755315256/" title="_MG_6436"><img src="https://c1.staticflickr.com/2/1630/25755315256_c9f7e3b892_z.jpg" width="640" height="427" alt="_MG_6436"></a><script async src="//embedr.flickr.com/assets/client-code.js" charset="utf-8"></script>

[Henk]

Potential bucket, probably worth trying to knock the price down a bit.

http://www.trademe.co.nz/a.aspx?id=1213429090

[Scubbo]

I just shamefully binned my fxr150 riding home last night, had a slow impact into back corner of a van who changed lane infront of me whilst lane splitting (I was going to fast for the wet road :bash:)

rode the bike home after, still running fine, damage is to the front fairing and front brake master cylinder banjoe loosened and dumped the brake fluid so brake wasnt working on ride back

whats it worth to someone you reckon? or is there a bucket racing newbie group I can join around auckland?

[F5 Dave]

A racing career awaits thee, fate has beckoned. The brave shall heed the call:headbang:

[Autech]

A sign!
A sign!
A sign from the racing Gods!




Sent from my iPhone using Tapatalk

[cotswold]

I just shamefully binned my fxr150 riding home last night, had a slow impact into back corner of a van who changed lane infront of me whilst lane splitting (I was going to fast for the wet road :bash:)

rode the bike home after, still running fine, damage is to the front fairing and front brake master cylinder banjoe loosened and dumped the brake fluid so brake wasnt working on ride back

whats it worth to someone you reckon? or is there a bucket racing newbie group I can join around auckland?

https://www.facebook.com/groups/BucketRacingNZ/

[TZ350]

326864

http://www.trademe.co.nz/motors/motorbikes/motorbikes/other/auction-1212574165.htm

Someone really should give this a good home.

[Scubbo]

http://www.trademe.co.nz/Browse/Listing.aspx?id=1224194751

was keen to get into bucket racing but to many hobbies and not enough money so... make an offer.

UPDATE: Sold to a bloke down south

[Grumph]

Already listed in the general for sale section of the forum.
17 X 3.5 rear and 17 X 2.5 front wire wheels. Unused.
Bearings have been swapped to suit 15mm axles.
Sprocket flange has been trimmed back 8mm to suit a roadrace application plus a part machined mount for a further inset sprocket will go with them.
Wave discs will go with them also.
They were bought for a small Post Classic project, now surplus to requirements.
These are dirt bike hubs so no cush drive or speedo drive provision.

Pickup preferred from Canterbury but transport could be arranged around the Nationals.

Edit SOLD - soon to be seen oop North.

[F5 Dave]

Wow. Someone give me a TDR250 these are begging for.

[husaberg]

Wow. Someone give me a TDR250 these are begging for.

Pretty sure the TDR250 has those rim sizes already, other than one wheel was 18. (can't remember if it was rear, for sure, although the front might have been 2.15 rather than 2.5)
It also had a larger front disk (320mm)

[F5 Dave]

They look good, 3" & 4.5" would be better for a 250 but ya know?
Perfect for a flash bucket.

[Grumph]

Perfect for a flash bucket.

That's what the importer thought. Of the two sets imported, neither has made it onto the track yet, the owners (and I include me...) have been happy to just look at them and occasionally fondle them.....Yow Ling has the other set now and is probably fondling them as I write...

[Yow Ling]

That's what the importer thought. Of the two sets imported, neither has made it onto the track yet, the owners (and I include me...) have been happy to just look at them and occasionally fondle them.....Yow Ling has the other set now and is probably fondling them as I write...

I was going to wait till Christmas day

[cotswold]

http://www.trademe.co.nz/a.aspx?id=1233699113

Made in ChiMa so must be good

[Grumph]

Made in ChiMa so must be good

Draws 10 - 15 amps....there's half the engine output gone.....

[F5 Dave]

I did wonder how that was going to be supplied. Clearly it looks too weedy to actually have that requirement.

Nice find. I think you should buy it.

Probability is it will double your horppower. (See what I did there?)

[Racey Rider]

Full rear brake system may be of use to someone. $60 with free freight.
http://www.trademe.co.nz/Browse/Listing.aspx?id=1232834919

[ac3_snow]

Wheels and wets $250.
Wheels are off fzr250 the model prior to 3ln, might be 2kr??(bearings were changed for different axle size) includes discs but no sprocket carrier, 2.5 rear 2.15 front.

Mikuni 24mm flat slide carb $80
Purchased brand new used for one weekend.

327628327629

[steveyb]

Several pairs of good, used Bridgestone 125GP/Moto3 slicks, soft compound, for sale.
One pair of 2016 style rain tyres also. Front is mint, rear about 1/3 to 1/2 used. Still plenty good.
$200 ono for slicks
$250 ono for the rain tyres.

Txt Oh two one nine 2 44 nine three. Tyres in Wellington.

Cheers

Steve

[Sketchy_Racer]

I'm selling up as we've bought a section and got to move house, so for sale is my beloved dyno.

It's a humble little inertia chassis dyno that was designed for doing bucket bikes, it has since been used for tuning many bikes, including a lap record setting NSR300.

It comes with everything ready to go minus laptop for screen (or can include for addition $200). That includes cooling fans and exhaust extraction as well as data acquisition module.

if you are interested I can arrange getting some photos and techinical specs sent though.

As for price i'm not sure, if you're interested get in touch 022-089-3234 or G.skachill@gmail.com

Cheers,
Glen

[Sketchy_Racer]

Bucket for sale: Suzuki RGV250 VJ21 Chassis with re-valved forks and suzuki GSXR-600 shock, re-sprung and re-vavled. Handles amazingly. Engine is Honda MB100 originally F5Daves motor, Runs well smooth power curve. Dynos at 19.3hp on dyno jet. has Ignitech igntion powering it on total loss. Runs RS125 slicks. Held lap record around Kaitoke on it until last weekend. Photos are old and changed tail piece since then but will give it a tart up and get some new pictures soon.
Want $2k

330344
330343
330342

[Sketchy_Racer]

Full setup ready to bolt on. 28mm throttle body

Open to offers

[F5 Dave]

Aww! And Aww! Still needs must mate, good luck.

[timg]

http://www.trademe.co.nz/Browse/Listing.aspx?id=1314953745&ed=true

[TZ350]

331044

Current bid $1400

http://www.trademe.co.nz/motors/motorbikes/motorbikes/sports/auction-1332712310.htm

[timg]

Anybody know of a CBR150 engine looking for a new home? Cheers

[TZ350]

331332

http://www.trademe.co.nz/a.aspx?id=1348688275

[TZ350]

331915

$110

http://www.trademe.co.nz/a.asp?id=1378383870&cc=602&pid=612132491&hbc=&member_hash=&ct=title-link&tm=email&et=602&mt=dd9b6545-f63a-4202-b9f8-9052c5d21f6e

Here we go, build a decent 2T engine, fit it to a FXR150 rolling chassis and Bobs you Uncle.

[mr bucketracer]

331915

$110

http://www.trademe.co.nz/a.asp?id=1378383870&cc=602&pid=612132491&hbc=&member_hash=&ct=title-link&tm=email&et=602&mt=dd9b6545-f63a-4202-b9f8-9052c5d21f6e

Here we go, build a decent 2T engine, fit it to a FXR150 rolling chassis and Bobs you Uncle.i say keep the fxr engine lol

[F5 Dave]

Where do you think your donors come from?

[mr bucketracer]

Where do you think your donors come from?donor what ?i have 4 fxr rollers lol

[F5 Dave]

Well sell em for 2 hundy each and get rich while people rehouse doggy TF engines.

[TZ350]

Where do you think your donors come from?

Blown up FXR's where the engine is not an economic fix, 4T's are expensive, 2T's not so much.

[husaberg]

Not bucket but bloody cheap

478.493401
200/55-17R KR449 N-TEC 2662 SOFT SLICK USA closeout special
was $ 403.65
now $ 101.78

http://www.forbesanddavies.co.nz/products/view/dunlop-race-slicks/

i spied it a link twr posted

[Grumph]

More parts clearout.
2 X RG400 barrels. Good bores, unmolested, original size.
One 400 head ( actually half a 400 head as it's been bandsawed off it's partner)
One RG500 head complete - meaning two heads in one piece. These will machine to suit the 400 bores.

$350ono Canterbury pickup or freight at purchasers expense.

[TZ350]

332833

https://www.trademe.co.nz/motors/motorbikes/motorbikes/classic-vintage/auction-1427947155.htm

2 stroke Bucket racer, great first bike or one to add to your existing fleet.
Unsure of the exact year.
Comes with lots of spare parts, few spare motors, one is apparently race prepped.
Selling as I don't use it

North Shore Auckland ..... Stanley mob 021 1138928

[F5 Dave]

Pickets old bike it looks.

[timg]

Cleaning out some stuff on TradeMe
GP125 slicks, RS125 front wheel & frame, Oko carb etc
https://www.trademe.co.nz/Browse/Listing.aspx?id=1436088374
https://www.trademe.co.nz/Browse/Listing.aspx?id=1436095130
https://www.trademe.co.nz/Browse/Listing.aspx?id=1436101688
https://www.trademe.co.nz/Browse/Listing.aspx?id=1436110274
https://www.trademe.co.nz/Browse/Listing.aspx?id=1436115879
https://www.trademe.co.nz/Browse/Listing.aspx?id=1436127314
https://www.trademe.co.nz/Browse/Listing.aspx?id=1436928178
https://www.trademe.co.nz/Browse/Listing.aspx?id=1436932234

[rc_36_rider]

Anyone got a 28mm oko or similar flat slide for sale for a bucket?

[husaberg]

Anyone got a 28mm oko or similar flat slide for sale for a bucket?
post above yours.....
oh it was a 32mm

[rc_36_rider]

post above yours.....
oh it was a 32mm

Yea, saw that one, too big for my motor.

[gav]

https://www.trademe.co.nz/Browse/Listing.aspx?id=1477624333

https://trademe.tmcdn.co.nz/photoserver/plusw/679176193.jpg

https://trademe.tmcdn.co.nz/photoserver/plusw/675071665.jpg

[FastFred]

333750

https://www.trademe.co.nz/motors/motorbikes/motorbikes/sports/auction-1485452374.htm?rsqid=8f0907b6e7db4270b14595c10179b 7ef

[FastFred]

333751

https://www.trademe.co.nz/motors/motorbikes/parts-for-sale/tyres/auction-1487829409.htm?rsqid=f793bfdf0bb24d0fb1b1a7a337be8 8e3

[cbfb]

Free rgv150 bits. Frame, tank, fairings etc

Get in quick as soon as I can be arsed it's going in the bin

Too lazy to post sorry pickup only

--------------

Gone sorry

[sidecar bob]

I have a complete ds80, kicks over, never tried to run it.
Really only any good for the engine $50
Tauranga.

[rc_36_rider]

Anyone looking for a R15 V2 race ECU? I got one then discovered the early V2 have a 26 pin ecu like the V1 so this is no use to me. cost me $277
Please PM if your interested
http://www.aracer-speedtek.com/English/ProductDetail.aspx?tid=15&pid=87

[TZ350]

335788 not my motor, just a picture of what is possible with the parts I have for sale.

This is your chance to make a supercharged water cooled 4 valve Honda 100 like this one.

Great collection of engines and engine parts, parts to kick start the project with:-

https://www.trademe.co.nz/Browse/Listing.aspx?id=1575950241

[Drew]

335788 not my motor, just a picture of what is possible with the parts I have for sale.

This is your chance to make a supercharged water cooled 4 valve Honda 100 like this one.

Great collection of engines and engine parts, parts to kick start the project with:-

https://www.trademe.co.nz/Browse/Listing.aspx?id=1575950241
I gave the complete(ish) one pictured to Nabbs. Someone motivate him.

[F5 Dave]

He has ways too much to achieve on my old 100.

[Grumph]

RG50 set up as a racebike - plus spare engine.

Don at Pitlane-in-the-country local to me has put this up on trademe today. I can't post a link sorry.
It's a bike with known ChCh history. Bit rough round the edges but an interesting project.

Down here they're rocking horse poo - I think I've only ever seen three.

[F5 Dave]

Oh yeah here it is.

https://www.trademe.co.nz/motors/motorbikes/motorbikes/classic-vintage/auction-1742577745.htm?rsqid=7fbb4d5b15d04ba7adaf4b1891d18 af2

Not too sure about this bit;

"Has a factory Suzuki race chamber. . "


:shutup:

[husaberg]

Oh yeah here it is.

https://www.trademe.co.nz/motors/motorbikes/motorbikes/classic-vintage/auction-1742577745.htm?rsqid=7fbb4d5b15d04ba7adaf4b1891d18 af2

Not too sure about this bit;

"Has a factory Suzuki race chamber. . "


:shutup:



The forks are around the wrong way or on the wrong side....
Or actually both.

[Grumph]

Oh yeah here it is.

https://www.trademe.co.nz/motors/motorbikes/motorbikes/classic-vintage/auction-1742577745.htm?rsqid=7fbb4d5b15d04ba7adaf4b1891d18 af2

Not too sure about this bit;

"Has a factory Suzuki race chamber. . "


:shutup:



The pipe apparently came via Grant Ramage back in the day...

[F5 Dave]

The strap at the back is gash, the header is almost as long as the rest of the pipe but heck I'm coming over all sentimental.

[Grumph]

The strap at the back is gash, the header is almost as long as the rest of the pipe but heck I'm coming over all sentimental.

You're not a morning person are you Dave....

[F5 Dave]

Clue is in the name. Mourning.

Just can't see a pipe like that being advertised as Suzuki factory racing when clearly it's someone has, in the spirit of Buckets I add, - had a go. And fair enough. But post Earnest's defection Suzuki didn't design that pipe.

Looks a fair enough deal though with those spares. Will need a rod kit having sat like that.

[mr bucketracer]

2 nsr 125 /250 barrels and new pistons , good bores with power valves 500 bucks

[TZ350]

2 nsr 125 /250 barrels and new pistons , good bores with power valves 500 bucks

MC18 or MC21??

[mr bucketracer]

I bought a mc 21 and a sp dry cluch engine .these barrels came with it but no idea what there off 339398339399maybe blow the numbers up on the barrels

[TZ350]

.

Yours are probably MC21's bottoms look the same so need to see the tops to be sure.

339402 MC21


339403 MC18

The heads are not interchangeable and the spigots are different diameters.

[timg]

Check out my TradeMe listings.
https://www.trademe.co.nz/Browse/Listing.aspx?id=1850125224

[Flettner]

Any CB125 twin, heads or complete engines out there, any year.

[Drew]

Any CB125 twin, heads or complete engines out there, any year.

You can get them new on aliexpress.

[Flettner]

You can get them new on aliexpress.

Where are they made? China I guess.

[F5 Dave]

In a factory in China presumably, but if it was Rajiexpress it would be on the side of the road in India and feature in a YooToob video.

[Flettner]

In a factory in China presumably, but if it was Rajiexpress it would be on the side of the road in India and feature in a YooToob video.

Ahrr, I guess Ill just have to cast one...
I started to build a 100 twin supercharged useing FZR parts but Bucket rules forbid ethanol fuel so I gave up. A new off road class uses a "bucket" rule template, 150cc, engine modification open but must be direct air cooled.
With ethanol I can live with air cooled. Perhaps a V twin with poxy Honda 50 heads? Or just bight the bullet and build exactly what I want, no compromise. Parallel twin would be best.

[Grumph]

FZR bottom end. Your own cast barrel - and a GSX250 Suzuki head. 8 valve DOHC, reasonable chamber shape. Not too big IMO.

[Flettner]

FZR bottom end. Your own cast barrel - and a GSX250 Suzuki head. 8 valve DOHC, reasonable chamber shape. Not too big IMO.

Air cooled?

[F5 Dave]

What's all this 4 stroke nonsense?

[Grumph]

Air cooled?

Yes. But central camchain tunnel. Nothing you can't solve.

Sorry Dave.

[Flettner]

What's all this 4 stroke nonsense?

New Vinduro class, I thought I'd like to enter something totally impractical but outragous. 150cc supercharged twin I think would hit the spot nicely.
Perhaps a CB200 would be a better base to start with. Sleeve it down but keep the stroke the same.

[F5 Dave]

L shaped uniflow with a half speed supplementary compressive chamber. I'll let you work out the details of how it works (Ihavent a clue, l'm more of a big picture kinda guy) but there's got to be a 3 stroke in there somewhere. ;)

[husaberg]

Suzuki and hobag do a 125 4v vtwin pretty sure its air cooled not as common as the 250 but very similar.

351468351469

i have a pretty tidy CL175 here might be a bit spendy

[Flettner]

Suzuki and hobag do a 125 4v vtwin pretty sure its air cooled not as common as the 250 but very similar.

351468351469

i have a pretty tidy CL175 here might be a bit spendy
Im a bit picky, dont want expensive or tidy, cause I will wreak it. And I do want a parallel twin.
This whole episode is just a bit of a gag so Im going to spend as little as possible.
Although CL175 would be right on the money, engine wise. Its going to have to be brought back down to 150cc, rules, but that is the only rule and air cooled. Ethanol, nitro, supercharge, whatever I want. My kind of class.
But thankyou anyway.