ducatilover's squidtastic pile of crap

[ducatilover]

How much boost is he planning on? Wonder how the crank and rods will hold up to it. I am thinking, not very well. Should just go with a twin screw supercharger instead, more low end boost

That dude is planning on 12psi to start with, motr later. It's got all the strong internals and a big bore kit.
I'd go with 6psi on a standard motor with lowered compression, not huge boost so detonation is not a big risk and it won't throw a rod if tuned right.
Superchargers are good, but, I think I'd need a stronger crank or a crank brace.

I like them, but are they bright enough?

They're kinda almost...maybe...not really? I don't know, they're awesome

[ducatilover]

Whipped this up from card, sitting on the wrong angle though.


Thoughts? I was thinking perhaps an inch out of it so it doesn't protrude so far?

[blackdog]

Whipped this up from card, sitting on the wrong angle though.


Thoughts? I was thinking perhaps an inch out of it so it doesn't protrude so far?

You'll need to pare that back to avoid a 'blinker' effect. It's hard enough to see at night without blanking out everything that's not in a metre wide corridor directly in front of you.

Like though, heading in the right direction.

[ducatilover]

You'll need to pare that back to avoid a 'blinker' effect. It's hard enough to see at night without blanking out everything that's not in a metre wide corridor directly in front of you.

Like though, heading in the right direction.

Yeah, will make it out of fiberglass or sheet metal and then do the inside, I can hide what's left of the loom in it and it looks nice and different

[bogan]

Looks good! and speaking of the blinkered effect, just put blinkers on one so it gives a low beam, compliance win

[ducatilover]

Looks good! and speaking of the blinkered effect, just put blinkers on one so it gives a low beam, compliance win

Genius!!!!!!!!!

[ducatilover]

Pulled my front wheel off today and got the top clamp on, bars at the right height too.
The speedo drive on the ZZR wheel is 2mm too thick, so there's 2mm clearance on one side and 6mm on the speedo side (between the disk and brake mounting brackets.) So the lower part of the fork leg will need to be machined to suit I suppose Pic whore time.

Top clamp on and headlight cover/thingy sitting pretty, cable ties rule.

Top clamp needs a polish!

Rear sets need to be tidied up too and a pic of the remounted brake res. and tidied up hose-clamps

[tigertim20]

Whipped this up from card, sitting on the wrong angle though.


Thoughts? I was thinking perhaps an inch out of it so it doesn't protrude so far?

that thing is going to limit the amount of road thats lit, which might be a problem.

[ducatilover]

that thing is going to limit the amount of road thats lit, which might be a problem.

What could possibly go wrong

[DrunkenMistake]

What could possibly go wrong

LIGHTS?
BWAHAHAHA WHO NEEDS LIGHTS?!

[tigertim20]

lights arent going to help when he cartwheels it again anyway

[MikeD400]

lights arent going to help when he cartwheels it again anyway

LOL, YOU didnt touch wood man his next cartwheel is on your head buddy and dont think this will be forgotten!

[DrunkenMistake]

lights arent going to help when he cartwheels it again anyway

LOL, YOU didnt touch wood man his next cartwheel is on your head buddy and dont think this will be forgotten!

I knew an Asian girl who could do a cartwheel and finish off by giving head.

[crystalball]

I knew an Asian girl who could do a cartwheel and finish off by giving head.

nice.

[MikeD400]

I knew an Asian girl who could do a cartwheel and finish off by giving head.

What happened? Did your mum make u flush her down the toilet??